Penny & Giles Robust design for arduous applications Return-to-center or return-to-end options Under-panel depth minimized to 9mm Rated for 40 million cycles Hall-effect sensor technology Dual outputs with sense and voltage span options IP67 sealing above panel Can be supplied as ‘base-only’ so the colored tabs can be fitted at final installation The JC1200 offers the next generation of paddle joystick from Curtiss-Wright to build on the success of the Penny & Giles potentiometric JC120. This new joystick utilizes non-contacting, Hall-effect sensing technology for long-life integrity of the output signal. Operating feel has been an important part of this new development to make this unit as smooth and easy to operate as possible throughout an industryleading 40 million cycle life. Hall-effect sensing eliminates contact wear and provides safety functionality via dual outputs, which can be set to positive or negative ramps, or a combination of both. Electronic robustness is assured with sealing of the internal PCB to a rating of IP65, while a joystick to panel rating of IP67 can be achieved. A choice of paddle ‘Tabs’ is available in nine different colors. These can be fitted at the factory or supplied as loose parts to be selected as part of the final installation process.

© 2023 Curtiss-Wright. All rights reserved. Curtiss-Wright accepts no responsibility for possible errors in catalogs, brochures and other printed material. Curtiss-Wright reserves the right to alter its products without prior notice. This also applies to products already ordered provided that such alterations can be made without affecting agreed specifications. All trademarks in this material are properties of their respective owners.

Code Description

OUTPUT SENSE JC1200-GEN-X-XX-X-XX Code Output 1: Positive slope Output 2: Negative slope Output 1: Positive slope Output 2: Positive slope Output 1: Negative slope Output 2: Negative slope

Code Description C Center PADDLE INSERT COLOR JC1200-GEN-X-XX-X-XX Color Description Colored tab not fitted Black Grey White Yellow Orange Red Purple Blue Green Applicable RAL Number Individual Colored Tab Part Number RAL 9005 RAL 7042 RAL 9003 RAL1023 RAL 2007 RAL 3028 RAL 4006 RAL 5017 RAL 6038

Dimensions - Spring Return to Center IDENTIFICATION—' LABEL FITTED HERE FORWARD DIRECTION MINIMUM PANEL THICKNESS See the sealing note SCREW TIGHTENING TORQUE RANGE 0.5 TO 0.65Nm

Dimensions - Spring Return to End MINIMUM PANEL THICKNESS See the sealing note SCREW TIGHTENING TORQUE RANGE 0.5 to 0.65Nm

Panel Mounting Details - Standard Minimum joystick separation is 2mm

Panel Mounting Details - Non-Standard Minimum joystick separation is 19mm 9 | Page

ELECTRICAL CONNECTIONS Molex 70553-0006 7-pin connector with gold-plated pins Recommended mating connector either: Molex 70400 14-56-2074 (connector and pin kit) or Molex 70066 50-57-9407 connector body plus 7 pins to the Molex number 70058 16-020082. Note: the mating connector must be fitted with gold-plated pins to ensure stable output from the joystick Standard Cables with a connector fitted are available from Curtiss Wright as follows: CW part number SA301649 – cable length 500 mm CW part number SA308599 – cable length 1,000 mm Pin

SPECIFICATIONS ELECTRICAL SUPPLY VOLTAGE SUPPLY CURRENT OVER-VOLTAGE PROTECTION SHORT-CIRCUIT PROTECTION TO SUPPLY Yes REVERSE POLARITY PROTECTION POWER-ON SETTLEMENT TEMPERATURE COEFFICIENT TRACKING ERROR OUTPUT CLAMPING Yes (1% above and below the Maximum and Minimum end voltage values) Note: Clamping limits still apply to output voltage after life OUTPUT TYPE Dual analogue ratiometric (crossed or parallel) OUTPUT RANGE: AS SUPPLIED 10-90% ±2% of supply voltage (0.5-4.5V nominal) – see after life note below 20-80% ±2% of supply voltage (1.0-4.0V nominal) – see after life note below CENTER VOLTAGE:...

CONDUCTED DISTURBANCE IMMUNITY 4KV contact (including connector pins) , 4KV Air POWER FIELD IMMUNITY ENVIRONMENTAL AND LEGISLATIVE OPERATING TEMPERATURE Thermal shock to EN 60068-2-14: 1999 Temperature and humidity to EN 60068-2-38: 2009 STORAGE TEMPERATURE Cold test to EN 60068-2-1: 1993 Dry heat to EN 60068-2-2: 1993 WATER AND DUST INGRESS Panel sealing performance is dependent on the stiffness and surface condition of the panel i.e. free of scratches. It is the responsibility of the customer to define the panel material and thickness to achieve the seal rating IP55 below panel, including connector...