• Robust design for arduous in-cab applications • Optional lever actuator profile • Hall-effect sensor technology • Rated for 3 million cycles of life • Dual-redundant electronic architecture • Outputs with sense and voltage span options • Dual supply to ensure a high level of signal integrity • Designed to allow contamination (liquid or dust) to pass through the mechanism without causing any damage The JC050 is a roller for use in joystick grips and other in-cab human-machine interfaces. A robust, return-to-center mechanism provides movement over a range of ±37°, with the thumbwheel having an option of a lever profile to ease operation. A compact mechanical design means the required under-panel space is just 23mm. The roller utilizes non-contacting, Hall-effect sensing technology that eliminates contact wear and provides for long-life integrity of the output signal, giving rise to a minimum operating life of 3 million cycles. Safety is enhanced via a fully dual-redundant electronic architecture made up of two power supplies and two sensing circuits, the outputs of which can be set to positive or negative ramps or a combination of both. Electronic robustness is assured with the enclosure sealing rated to IP67.

© 2021 Curtiss-Wright. All rights reserved. Curtiss-Wright accepts no responsibility for possible errors in catalogs, brochures and other printed material. Curtiss-Wright reserves the right to alter its products without prior notice. This also applies to products already ordered provided that such alterations can be made without affecting agreed specifications. All trademarks in this material are properties of their respective owners.

OUTPUT SENSE Output 1: Positive slope Output 1: Positive slope Output 1: Positive slope Output 1: Flat with Positive slope Output 2: Negative slope Output 2: Positive slope Output 2: No Output Output 2: Negative slope with Flat

The Output Range (at ends of travel) is based on a regulated 5V supply. The general output tolerance is ±2% of Vs Code Description CABLE TYPE Code Description The Standard Duty cable is recommended for fixed cable routing applications such as panel installations; available for F055 and C205 cable length options The High Cycle cable is recommended for dynamic application such as joystick grips; available for F350 option CABLE LENGTH Code Description F055 Flying Lead with 55mm cable length - SD cable type C205 Flying Lead with 205mm cable length and 3-way Molex 35507-0300 Connector - SD cable type...

Color Description ■ Black Grey White Yellow Orange I Red Purple Blue Green Availability Standard and available Special order with minimum order quantity Special order with minimum order quantity Special order with minimum order quantity Special order with minimum order quantity Special order with minimum order quantity Special order with minimum order quantity Special order with minimum order quantity Special order with minimum order quantity Color Description Black Grey White Yellow Orange Red Purple Blue Green Availability Standard and available Special order with minimum order quantity Special...

INSTALLATION MECHANICAL Dimensions Forward Orientation Arrow Thumb Wheel option – with paddle Forward Orientation Arrow Roller Wheel option – without paddle

Panel Cut-out Details The following details show the hole that should be cut in the mounting panel Curtiss Wright recommend that a panel thickness of 1.1mm to 5.4mm is used The JC050 is a press fit into the panel and does not require any additional fixings Panel Mounting Details - standard There is a minimal spacing between two JC050 rollers to ensure there isn’t any influence on one rollers output from the other rollers magnet. In a standard mounting configuration the minimal gap is detailed below:

The JC050 is supplied with up to 6 cables with the colors and functions below The SD Cables are size 28 AWG (7/0.120), PTFE insulated and unscreened The HC Cables are size 30 AWG (19/0.060) PTFE insulated and unscreened Cable Color Molex Connector Pin Function Pin 2 Output 1 Signal +5V to Output Sensor 2 0V Output 2 Sensor Output 2 Signal This connector is only available as a 3-way option and with the 205 mm long SD type cable

SPECIFICATIONS ELECTRICAL SUPPLY VOLTAGE OUTPUT VOLTAGE CENTER REFERENCE TOLERANCE OF OUTPUT VOLTAGE AFTER LIFE (including temperature effects) End of travel positions: ±3% Center position: ±3% OUTPUT SENSE The dual outputs can be configured to have positive ramps, a combination of positive and negative ramps or full voltage range over half travel from each sensor with constant (low end of selected voltage range) output in the other half travel CURRENT CONSUMPTION TRACKING ERROR POWER ON SETTLEMENT TIME OVER VOLTAGE PROTECTION SHORT CIRCUIT PROTECTION Output to ground and output to supply SUPPLY...

ENVIRONMENTAL & LEGISLATIVE OPERATING TEMPERATURE STORAGE TEMPERATURE ENVIRONMENTAL PROTECTION VIBRATION (SINUSOIDAL) VIBRATION (RANDOM) FREE-FALL DROP SALT SPRAY MTTFd Cold Test: Dry Heat: The roller has a design where contamination (liquid or dust) can pass through the mechanism without causing any damage and an IP67 protection of the electronics 25gn, 10ms, 500 bumps in each of 6 directions 50g, 6ms, half sine, 3 shocks in each of 6 directions IMPORTANT INFORMATION Whilst Curtiss-Wright Industrial Division - Penny & Giles has designed this joystick to meet a range of applications it is the...