• Robust design for arduous in-cab applications • Optional mechanical over-press feature at either ends of travel • Hall-effect sensor technology • Rated for 1 million cycles of life • Dual-redundant electronic architecture • Outputs with sense and voltage span options • Dual supply to ensure a high level of signal integrity • Designed to allow contamination (liquid or dust) to pass through the mechanism without causing any damage The JC040 is a proportional rocker for use in joystick grips and other in-cab human-machine interfaces. Two robust, return-to-center operating options are available: a ±25° movement from center; or a ±20° movement with an over-press feature, which can be included in both directions of movement or just one, used to indicate a different mode of machine operation. In all versions, a compact mechanical design means the required underpanel space is just 21 mm. The rocker utilizes non-contacting, Hall-effect sensing technology that eliminates contact wear and provides for long-life integrity of the output signal, giving rise to a minimum operating life of 1 million cycles. Safety is enhanced via a fully dual-redundant electronic architecture made up of two power supplies and two sensing circuits, the outputs of which can be set to positive or negative ramps or a combination of both. Electronic robustness is assured with the enclosure sealing rated to IP67.

© 2023 Curtiss-Wright. All rights reserved. Curtiss-Wright accepts no responsibility for possible errors in catalogs, brochures and other printed material. Curtiss-Wright reserves the right to alter its products without prior notice. This also applies to products already ordered provided that such alterations can be made without affecting agreed specifications. All trademarks in this material are properties of their respective owners.

OUTPUT SENSE Code Description Output 1: Positive slope Output 1: Positive slope Output 2: Negative slope Output 2: Positive slope DETENT START DETENT START DETENT START

DETENT START

The detents provide a snap feel at ±20° (18% and 82% output voltage) that can be used in a control system to generate a specific response e.g. return to dig, rapid travel etc. Code Description 1F 1 Forward position detent IB 1 Backward position detent 2D Both detents fitted CABLE LENGTH Code Cable Length in mm

INSTALLATION MECHANICAL Dimensions Forward orientation mark

Panel cut-out/Mounting Details The following details show the hole that should be cut in the mounting panel Curtiss-Wright recommend that the JC040 rocker is mounted using a minimum of two M3 x 6mm female, self-clinching standoffs (e.g. PEM ref. CSS M3-6) fitted to the back of the panel at diametrically opposite positions. The standoffs are used in conjunction with two M3 x 6mm washer head screws. The screws should be tightened to a torque of 0.4Nm to 0.7Nm with a minimum panel thickness of 3 mm.

Panel Mounting Details - standard There is a minimal spacing between two JC040 rockers to ensure there isn’t any influence on one rockers output from the other rockers magnet. In a standard mounting configuration the gap is: ELECTRICAL CONNECTIONS The JC040 is supplied with 6 wires with the colours and functions below The wires are size 30 AWG (19/0.06), PTFE insulated and unscreened with a maximum outside diameter of 0.65mm Wire Color

SPECIFICATIONS ELECTRICAL SUPPLY VOLTAGE OUTPUT VOLTAGE CENTER REFERENCE OVER-PRESS VOLTAGE (if fitted) TOLERANCE OF OUTPUT VOLTAGE AFTER LIFE (including temperature effects) Reverse end of travel position: -3% to +2% Reverse detent positon: -4% to +3% Centre position: -2.5% to +2% Forward detent position: -3% to +4% Forward end of travel position: -2% to +3% OUTPUT SENSE The dual outputs can be configured to have positive ramps or a combination of positive and negative ramps CURRENT CONSUMPTION TRACKING ERROR POWER ON SETTLEMENT TIME OVER VOLTAGE PROTECTION SHORT CIRCUIT PROTECTION Output to...

ENVIRONMENTAL & LEGISLATIVE OPERATING TEMPERATURE STORAGE TEMPERATURE ENVIRONMENTAL PROTECTION The rocker has a design where contamination (liquid or dust) can pass through the mechanism without causing any damage and an IP67 protection of the electronics VIBRATION (SINUSOIDAL) VIBRATION (RANDOM) 25gn, 10ms, 500 bumps in each of 6 directions FREE-FALL DROP 50g, 6ms, half sine, 3 shocks in each of 6 directions SALT SPRAY IMPORTANT INFORMATION Whilst Curtiss-Wright Industrial Division - Penny & Giles has designed this joystick to meet a range of applications it is the responsibility of the customer...