Catalogs >
Curtis Instruments >
AC Induction and PMAC Motor Controllers

AC Induction and PMAC Motor Controllers
10Pages

Catalog excerpts

AC Induction and PMAC Motor Controllers - 1

Motor Controllers AC Induction and PMAC Motor Controllers SERIES Logos Curtis MarCom 2014

AC Induction and PMAC Motor Controllers - 2

A range of controllers (inverters) for the speed and torque control of 3-phase AC motors. Intended for use as electric traction or hydraulic pump motor controllers for mobile, on-vehicle applications that use a SERIES Logos nominal battery supply. 24-96 VDC The ‘SE’ Advantage The Curtis ‘SE’ AC controllers utilize the latest technology to increase the peak current ratings for each size of controller. For a given rating, the SE models are smaller and lower cost than previous Curtis AC controllers, benefits that are highly advantageous for all types of applications. Only Curtis AC can offer:...

Open the catalog to page 2

AC Induction and PMAC Motor Controllers - 3

FEATURES Increased Performance, Improved Functionality ► Higher peak current rating allows use of a physically smaller controller for a given load, for easier installation in any vehicle. ► CE marked as a programmable safety device under EN ISO 13849-1. ► Models available for 250A-1000A output at 24-96V system voltages. These are true 2 minute RMS ratings, not short duration 'boost' ratings. ► Enhanced 64 MHz micro and additional FLASH memory doubles the available VCL code space and provides more than twice the VCL execution speed. ► VCL-configurable CAN 'mailboxes' provide highly flexible...

Open the catalog to page 3

AC Induction and PMAC Motor Controllers - 4

S~ SERIESM ocJels 1232SE / 1234SE / 1236SE / 1238SEFUNC TIONAL SAFETY DATA Safety Function

Open the catalog to page 4

AC Induction and PMAC Motor Controllers - 5

SYSTEM ACCESSORIES SERIES Logos Curtis MarCom 2014 The Curtis Model 1313 Handheld Programmer is ideal for setting parameters and performing diagnostic functions. The Curtis Model 1352 CANbus I/O expansion module features 9 I/O pins, including 6 proportional valve drivers. This module can be used to further expand the I/O capability of Curtis AC motor controllers using VCL. The Curtis Model 1222 is an AC induction motor controller for ‘steer by wire’ electric power steering systems and is the ideal partner for the ‘SE’ Controllers on vehicles such as reach trucks, order pickers, stackers and...

Open the catalog to page 5

AC Induction and PMAC Motor Controllers - 6

WIRING DIAGRAM 1232 AC Induction Motor Controller SERIES Logos TYPICAL WIRING COIL RETURN SWITCH 6 SWITCH 7 SWITCH 8 LOAD PUMP PROP. HOLD CONT VALVE VALVE DRIVER 4 PV DRIVER DIGITAL DRIVER 6 DIGITAL DRIVER 7 EMERGENCY STOP MOTOR TEMP. INPUT THROTTLE WIPER W +5V (100mA) PHASE A ENCODER PHASE B I/O Gnd B− B– POSITION ENCODER SERIAL PORT 4 PIN MOLEX

Open the catalog to page 6

AC Induction and PMAC Motor Controllers - 7

SERIES Logos DIMENSIONS mm (typical) STATUS LEDs

Open the catalog to page 7

AC Induction and PMAC Motor Controllers - 8

SERIES Logos DIMENSIONS mm (typical) STATUS LEDs

Open the catalog to page 8

AC Induction and PMAC Motor Controllers - 9

SERIES Logos DIMENSIONS mm (typical) STATUS LEDs

Open the catalog to page 9

AC Induction and PMAC Motor Controllers - 10

SERIES Logos DIMENSIONS mm (typical) Status LEDs Two year limited warranty from time of delivery. is a trademark of Curtis Instruments, Inc. Specifications subject to change without notice

Open the catalog to page 10

AC Induction and PMAC Motor Controllers 10Pages

Catalog excerpts

All Curtis Instruments catalogs and technical brochures

AC Induction and PMAC Motor Controllers
10Pages