T-620H-CPF Hydrulic Hand Pump Manual
17Pages

T-600 Series Operation Manua_ TEST & CALIBRATION INSTRUMENTS

Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features and Parts Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Generating Pressure . . . . . . . . . . . . . . . . . . . . . . ....

Overview INTRODUCTION     The T-600 Series hydraulic hand pump you have chosen, is an extremely effective pressure pump, and we are confident that it will live up to your expectations. Over the course of many years, we have acquired extensive knowledge of industrial precision pressure calibration. This expertise is reflected in our products, all of which are designed for daily use in an industrial environment. If you have any ideas or suggestions for ways we might improve our products, we would be very interested in hearing from you. The T-600 Series hydraulic hand pumps, designed by...

FEATURES AND PARTS LISTS     The T-600 series hand pumps feature a 0.5 pint/20 cl built-in oil reservoir, vent valve and fine adjust knob. The pump has two pressure ports – one for the device under test and one for the reference indicator. Parts Included with Pump (T-620 and T-620H) Fill Plug XX Reference Pressure Port (1/4" NPT Female, swivel) No additional fittings are included for the Reference Pressure Port. XX Device Under Test Pressure Port Part Number 0.61 meter hose with 1/4" NPT Female connector 1/4" NPT Male x 1/4" BSP Female adapter Parts Included with Pump (T-620H-CPF) Check...

Parts Included with Pump Systems for JOFRA Reference Indicators System C CXX CHX (T-620) (T-620H) Part Number 1/4" NPT Male to 1/4" BSP Female Fitting 1/8" BSP Male to 1/4" NPT Male Fitting 1/8" BSP Male to 1/4" BSP Female Fitting 0.61 meter hose, 1/4" NPT Female connection Test Leads; Red & Black, including clips Pack Tape (1 roll) Shoulder Strap Aluminum Carrying Case Waterproof Carrying Case available with drained pumps. So when ordering, add -E-W to designate a drained pump in a waterproof case. See ternately, you may order a Pump System C with a Waterproof Carrying Case. Waterproof...

Parts Included with Pump Systems for Crystal Reference Indicators Carrying Case Options Part Number 3/8" BSP Male to CPF Male Fitting 5/16-24 SAE Male to CPF Female Fitting CPF Female to 1/4" NPT Female Fitting CPF Female to 1/4" BSP Female Fitting CPF Female to 1/8" NPT Male Fitting CPF Male Plug Fitting 1 meter CPF Male Hose O-ring and Lock Clip Case. Waterproof Carrying Cases are only available with drained pumps. So when ordering, hydraulic fluid. Alternately, you may order a Pump System C with a Waterproof Carrying Pump Systems C are delivered with an Aluminum Carrying Case with a pump...

Safety Instructions SAFETY INSTRUCTIONS     Please follow the instructions and procedures described in this manual. They are designed to help you get the most out of your pressure system and to avoid any personal injuries and/or damage to the system. Please notice the pump comes in 2 different pressure ranges. Therefore it is very important to check the version of the pump to avoid over-pressurizing the indicator. Note: The product liability only applies if the pressure system is subject to a manufacturing defect. This liability becomes void if the user fails to follow the maintenance...

Generating Pressure Follow these steps in order to operate the pump correctly. See the diagram on page 2 for reference.. Connecting to the Pump 1 Remove the fill plug and fill the reservoir approximately 2/3 full of test fluid. !!CAUTION: Do not use solvents , alcohol, or synthetic fluids that will adversely affect the operation of the pump. Please refer to the Recommended Test Fluids section on page 10 for more information. 2 Connect and tighten the fill plug. 3 Turn the pressure vent valve and fine adjust knob counter-clockwise until fully open. 4 Prime the system by pumping the movable...

Applying Pressure !!CAUTION: Ensure all fittings and devices are connected correctly and without leaks. 1 Ensure the device-under-test and reference indicator are powered on and are indicating pressure readings. Disconnecting from the Pump 1 Release pressure by turning the vent valve counter-clockwise. 2 Remove the device under test. 2 Turn the pressure vent valve and fine adjust knob counter-clockwise until fully open. 3 Zero the reference indicator. 4 Turn the pressure vent valve clockwise until fully closed. (Close by hand only.) 5 Operate the handle to apply pressure until the target...

Connection Diagrams JOFRA REFERENCE INDICATORS CALIBRATION INSTRUMENTS Handheld Pressure Calibrator Industrial Pressure Indicator MKII 126029 1/4" MNPT/1/2" FBSP (to DPCJ Sensor) * These parts are included with the pump. All other parts are supplied as part of a pump system, or may be ordered separately. All BSP connections require bonded seals. Denotes areas where thread-sealing tape is required. T-600 Series Pump Operation Manual

CRYSTAL REFERENCE INDICATORS Pressure Calibrator Digital Test Gauge Intrinsically Safe 1/8" Quick Test NPT Male 1/8" NPT Male 1/4" Quick Test NPT Male Reference Recorder Additional NPT sizes available in non-CPF MP adapters Thread tape required here. 1/4" Quick Test NPT Female 1/8" Quick Test NPT Female Intrinsically Safe 1/2" Quick Test NPT Female Additional NPT sizes available in non-CPF MP adapters for Foxboro, Rosemount, & Yokogawa T-Union (Female) Bulkhead (Female to Female) M20 x 1.5 Quick Test Female ADDITIONAL MPM-PLUG * * These parts are included with the T-620H-CPF pump....