1. Catalogs
  2. Critical Process Filtration
  3. Service Nylon 6,6 Capsules

Service Nylon 6,6 Capsules

Service Nylon 6,6 Capsules

Service Nylon 6,6 Capsules

Product catalog summary
Construction Materials: The GNM Capsule Filters are constructed using polypropylene for the housing, media support, end caps, center core, and outer support cage. The filtration media is made from Nylon 6,6 membrane, and the sealing method is thermal bonding.
Applications: These filters are suitable for processing water, solvents, DI water, chemicals, inks, and dyes. They are hydrophilic and designed for critical applications involving a wide range of liquids.
Specifications: The filters operate at a maximum liquid pressure of 80 psi and gas pressure of 60 psi at 20°C. The operating temperature is 43°C at 30 psi in water. Forward and reverse differential pressures are 50 psid and 40 psid, respectively. The recommended changeout pressure is 35 psid.
Flow Rate and Filtration Area: The filters are available in various lengths with corresponding filtration areas, ranging from 1.0 ft² for a 2” capsule to 21.0 ft² for a 30” capsule. The pore sizes range from 0.03 μm to 1.2 μm, with flow rates provided in GPM and LPM.
Sanitization/Sterilization: The filters can be autoclaved at 250°F for 30 minutes in multiple cycles. Chemical sanitization is limited to 1% hydrogen peroxide or a combination with peracetic acid. They are not suitable for steam use.
Compliance: The filters meet FDA requirements for food and beverage processing and comply with relevant CFR sections. They also adhere to European Commission Regulation EU/10/2011.
Quality Assurance: Manufacturing follows ISO 9001:2008 standards, with real-time monitoring and traceability of materials and processes. The production system is sophisticated, ensuring high-quality output.
Ordering Information: Filters can be ordered based on micron rating, length, inlet, and outlet specifications. An example order number is provided for reference.
See more

Catalog excerpts

Service Nylon 6,6 Capsules-1

GNM Capsule Filters Nylon 6,6 Membrane Applications Process Water Inks & Dyes GNM capsules are hydrophilic and manufactured with high quality Nylon 6,6 membrane for critical applications in the processing of a wide range of liquids. The GNM capsules are designed for general purpose use wherever a cost effective pleated membrane capsule filter is required. GNM capsule filters are flushed with high purity water to remove manufacturing debris. These cartridge modules are also batch tested for integrity before release. High quality, hydrophilic membrane Cost effective pleated membrane capsule For critical applications in a wide range of liquids GNM Capsule Filters - Filtration Area Capsule Length The following table represents typical water flow at a one psi (69 mbar) pressure differential across a single 2 inch capsule with 1.0 ft² (930 cm²) of media with 1/2” FNPT ports. The test fluid is water at ambient temperature. Higher pressure drops are acceptable, but as flows increase the pressure drop of the housing becomes more apparent. 0.03 μm Pore Size * For approximate flow rates for 5” through 30” capsules, refer to the appropriate cartridge data sheet Construction Materials Maximum Operating Parameters Liquid Operational Pressure Filtration Media Gases Operational Pressure Media Support Operating Temperature Center Core Outer Support Cage Sealing Method Thermal Bonding Forward Differential Pressure 50 psid (3.4 bard) at 20 °C (68 °F) Reverse Differential Pressure Recommended Changeout Pressure General Service Grade Flow Rate / Filtration Area

 Open the catalog to page 1
Service Nylon 6,6 Capsules-2

All Critical Process Filtration capsule filters are designed to meet the FDA requirements for processing food and beverage products. The materials used to construct GNM capsule filters are listed by the FDA as appropriate for use in articles intended for repeated food contact as specified in Title 21 CFR sections 174.5, 177.1500, 177.1520, 177.1630, 177.2440 and 177.2600 as appropriate. Membrane filters comply with Title 21 CFR sections 210.3 (b)(6) and 211.72, for non-fiber releasing filters. All materials used to make the filters are listed in European Commission Regulation EU/10/2011, Annex...

 Open the catalog to page 2

All Critical Process Filtration catalogs and technical brochures

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.