Catalogs >
CRE TECHNOLOGY >
synchro compact hmi core standard wiring schematics revision a 19-05-2019

synchro compact hmi core standard wiring schematics revision a 19-05-2019
1 / 18Pages

Catalog excerpts

synchro compact hmi core standard wiring schematics revision a 19-05-2019 - 4

SYNCHRO COMPACT HMI / CORE STANDARD WIRING SCHEMATICS Module Rear / Core view PAGE 04 ◄ ► 03 05

synchro compact hmi core standard wiring schematics revision a 19-05-2019 - 5

CORE VERSION MOUNTING SCREWS DIMENSIONS Created: 09/05/2019 SYNCHRO COMPACT HMI / CORE STANDARD WIRING SCHEMATICS Dimensions / Panel cut PAGE

Open the catalog to page 5

synchro compact hmi core standard wiring schematics revision a 19-05-2019 - 6

SYNCHRO COMPACT HMI / CORE STANDARD WIRING SCHEMATICS Single line diagram PAGE 06 ◄ ► 05 07

Open the catalog to page 6

synchro compact hmi core standard wiring schematics revision a 19-05-2019 - 7

SYNCHRO COMPACT HMI / CORE STANDARD WIRING SCHEMATICS * Note1: Shall voltage transformers be required, refer to technical documentation PAGE Voltages and currents sensing 07 06 ►

Open the catalog to page 7

synchro compact hmi core standard wiring schematics revision a 19-05-2019 - 8

To inputs / outputs circuitry Module power supply 7...38vVdc * Note 1 COMPACT SYNCHRO * Note1: Example given with use of a 24Vdc battery charger, but applies identically with 12Vdc PAGE SYNCHRO COMPACT HMI / CORE FIRST RELEASE STANDARD WIRING SCHEMATICS Power supply and shield connection 07

Open the catalog to page 8

synchro compact hmi core standard wiring schematics revision a 19-05-2019 - 9

Breaker potion / Synch request / Spare ( Spare Configurable digital inputs CD O CD O 9 * Note 1: Default setting, can be adjusted via PC software as desired SYNCHRO COMPACT HMI / CORE STANDARD WIRING SCHEMATICS Digital inputs PAGE 09 ◄ ► 08 10

Open the catalog to page 9

synchro compact hmi core standard wiring schematics revision a 19-05-2019 - 10

Module +Vcc SENSOR CONNECTION EXAMPLES Module +Vcc Configurable analog inputs * Note 1 COMPACT SYNCHRO * Note1: Analog inputs can be used with resistive sensors (max. range 0-500 Ohms), with external 20mA current transducers fitted with a 30-ohm 1/4 Watt resistor or as additional digital inputs ** Note2: Ensure engine body and 0Vcc are connected in case of use of a single-wire sensor *** Note3: The common analog input terminal must have a direct connection to the –Batt terminal of the controller PAGE SYNCHRO COMPACT HMI / CORE FIRST RELEASE STANDARD WIRING SCHEMATICS

Open the catalog to page 10

synchro compact hmi core standard wiring schematics revision a 19-05-2019 - 11

COMPACT SYNCHRO Configurable digital outputs J1 * Note1: Maximum output current is 1.8 Amps PAGE SYNCHRO COMPACT HMI / CORE FIRST RELEASE STANDARD WIRING SCHEMATICS

Open the catalog to page 11

synchro compact hmi core standard wiring schematics revision a 19-05-2019 - 12

SYNCHRO COMPACT HMI / CORE STANDARD WIRING SCHEMATICS Relay outputs PAGE 12 ◄ ► 11 13

Open the catalog to page 12

synchro compact hmi core standard wiring schematics revision a 19-05-2019 - 13

SYNCHRO COMPACT HMI / CORE STANDARD WIRING SCHEMATICS * Note1: Refer to the engine technical sheet to set the number of teeth PAGE

Open the catalog to page 13

synchro compact hmi core standard wiring schematics revision a 19-05-2019 - 14

COMPACT SYNCHRO Voltage control output Speed control output SPEED REGULATOR VOLTAGE REGULATOR * Note1: Settings vary upon the type of regulator used. Refer to the technical sheet for more information PAGE SYNCHRO COMPACT HMI / CORE FIRST RELEASE STANDARD WIRING SCHEMATICS Speed & voltage control 13

Open the catalog to page 14

synchro compact hmi core standard wiring schematics revision a 19-05-2019 - 15

COMPACT SYNCHRO TO OTHER MODULES ** Note 2 * Notel: Embedded 120-ohm resistance to be bridged to CAN H terminal on first and last bus module only ** Note2: CAN 1 is dedicated to inter-module communication. CAN options are available on CAN2 SYNCHRO COMPACT HMI / CORE STANDARD WIRING SCHEMATICS

Open the catalog to page 15

synchro compact hmi core standard wiring schematics revision a 19-05-2019 - 16

COMPACT SYNCHRO Distance between node and module should not exceed 30 centimeters Notel: Bus end 120-ohm resistor to be placed between CAN L and CAN H terminal on last equipment only SYNCHRO COMPACT HMI / CORE STANDARD WIRING SCHEMATICS

Open the catalog to page 16

synchro compact hmi core standard wiring schematics revision a 19-05-2019 - 17

SYNCHRO COMPACT HMI / CORE STANDARD WIRING SCHEMATICS Engine control PAGE

Open the catalog to page 17

synchro compact hmi core standard wiring schematics revision a 19-05-2019 - 18

SPARE INFORMATION SPARE INFORMATION SPARE INFORMATION SPARE INFORMATION SPARE INFORMATION SYNCHRO COMPACT HMI / CORE STANDARD WIRING SCHEMATICS Digital output terminals PAGE 18 ◄ ► 17

Open the catalog to page 18