Catalog excerpts
CORNELL PUMP COMPANY
Open the catalog to page 1SOLIDS HANDLING VC (vertical coupled motor bracket) Generously sized bearings to maximize B-10 bearing life Cycloseal® design: no venting or flushing required SOLIDS HANDLING Cornell Solids Handling pumps are used for waste water, sludge, sewer systems, stringy material, de-watering, abrasive transfer, canneries, construction, dredging, lumber mills, slush ice, reclamation plants and foundry or mill slag. Heavy stress proof steel shaft (or 17-4 pH Stainless Steel) Replaceable 416 Stainless Steel shaft sleeve Back pull-out design for ease of maintenance Impeller back vanes for reduced axial...
Open the catalog to page 2SOLIDS HANDLING DELTA™ IMPELLER DELTA™ STYLE PUMPS The trailing edges of Cornell’s Delta™ impeller vanes extend continuously across the pump’s suction entrance to reduce low pressure areas. Two distinct vortices are created which pass solids through the impeller. The absence of sharp impeller edges prevents hang-up of stringy materials. Many of our enclosed impeller type pumps can be retrofitted with Delta™ style impellers. Delta™ pumps are available in 3 x 3”, 4 x 4”, 6 x 6”, 8 x 8” and 10 x 10” sizes. Capacities range from 50 to 5,000 GPM and heads range from 10 to 450 feet. CHOPPER...
Open the catalog to page 3CLEAR LIQUID PUMPS Cornell Clear Liquid pumps are used for commercial and residential irrigation, golf course and lawn maintenance, aqua culture, fountains, breweries, laundries, cooling towers, fire fighting, reverse osmosis feed, and water boosters. WATER BOOSTER LIP SEALS (FOR BEARING PROTECTIONS) OVERSIZED BEARINGS REPLACEABLE SHAFT SLEEVE SUCTION WEAR RING The W, Y, R and H series pumps are available in a wide range of materials with discharge sizes ranging from 1 to 10 inches, heads to 450 feet TDH, and flow rates up to 7,000 GPM. FRAME (OPTIONAL OIL LUBRICATIONS FOR EXTREME...
Open the catalog to page 4HEAVY DUTY AUTO-COUPLING ASSEMBLY - Discharge elbow with lift out sealing flange assemblies allow for pump service without the need to disconnect plumbing. Available for submersible pumps over the weight limit of STANDARD DUTY auto-couplings or for larger installations requiring a HEAVY DUTY base. • Ductile iron construction • Guide rail supports designed to accept standard pipe rails • O-ring and rubber face sealing ring • Non-Sparking Design available for certain sizes (contact factory) Cornell offers different impeller designs for liquid wastewater applications. Cornell's delta style...
Open the catalog to page 5HYDRO-TURBINE STANDARD TURBINE CONSTRUCTION: • Cast Iron, Bronze fittings optional, Ductile Iron, Steel, Bronze, Stainless Steel. • Mechanical shaft seal is standard, packing is optional. • Standard ODP generatoroptional TEFC. • Hydro blue, double applied paint. 10TR2S AND 5TR4S IN THE CITY OF BURBANK, CALIFORNIA - ENERGY RECOVERY PROJECT PUMP STATION BYPASS Cornell Redi-prime® pumps are designed with the suction larger than the discharge. This provides more flow due to reduced friction losses. Cornell’s priming system was specifically designed with the environment in mind. By using a...
Open the catalog to page 6ADDITIONAL PRODUCTS HYDRAULIC SUBMERSIBLE PUMPS Cornell’s DDuraSub™ uses a heavy duty pump end and bearing frame for direct coupling to a hydraulic motor. The DuraSub™ has a modular design which allows standard Cornell pump ends to be used as a Hydraulic submersible pump. • Available for most Cornell pump models • Hydraulic motor driven • Various adapter plates available for hydraulic motor fit • Heavy duty shaft / bearing frame assembly and wet end construction • Premium wet end efficiencies reduce horsepower requirements • Heavy duty pumps ends for long service life and reliability MX...
Open the catalog to page 7MARKET AND PRODUCT LINE CORNELL PUMP COMPANY CORNELL PUMP COMPANY CORNELL PUMP COMPANY FOOD PROCESS FOOD PROCESS CORNELL PUMP COMPANY END GUN BOOSTER PUMP CORNELL PUMP COMPANY CORNELL PUMP COMPANY CUTTER PUMPS CORNELL PUMP COMPANY CORNELL PUMP COMPANY CORNELL PUMP COMPANY HYDRO TURBINE HYDRAULIC SUBS CORNELL PUMP COMPANY MINE DEWATERING CORNELL PUMP COMPANY CORNELL PUMP COMPANY CORNELL PUMP COMPANY CORNELL PUMP COMPANY CORNELL PUMP COMPANY MANURE PUMPS MINING PUMPS DESIGNED FOR COARSE ABRASIVES FOR CENTER PIVOT IRRIGATION STANDARD SPECIFICATIONS • Models Available - 4NNT, 6NNT, 8NNT, etc. •...
Open the catalog to page 8All Cornell Pump catalogs and technical brochures
-
CO-PILOT
4 Pages
-
CHOPPER PUMP
4 Pages
-
High Flow Low Head Pumps
4 Pages
-
Water Transfer Brochure
8 Pages
-
Run-Dry brochure
4 Pages
-
CD4MCu
4 Pages
-
SUBMERSIBLES
2 Pages
-
STX SERIES
8 Pages
-
SLURRY CURVES
12 Pages
-
SLURRY PUMPS
8 Pages
-
REPLACEMENT PARTS
1 Pages
-
REDI-PRIME®
8 Pages
-
MX SERIES
8 Pages
-
MP SERIES
8 Pages
-
IMMERSIBLE MOTORS
2 Pages
-
HYDRAULIC SUBMERSIBLES
4 Pages
-
EDGE END GUN BOOSTER
4 Pages
-
CYCLOSEAL
8 Pages
-
CUTTER PUMP
8 Pages
-
CD4CMu
4 Pages
-
WATER TRANSFER
8 Pages
-
REFRIGERATION
8 Pages
-
OIL and GAS
8 Pages
-
MX MINING SERIES
8 Pages
-
MINING BROCHURE
8 Pages
-
MANURE PUMP BROCHURE
8 Pages
-
FOOD PROCESS BROCHURE
8 Pages
-
AGRICULTURE BROCHURE
8 Pages
Archived catalogs
-
Industrial Brochure
8 Pages
-
CORNELL PUMP COMPANY INDUSTRIAL
12 Pages