M 30 RC
2Pages

{{requestButtons}}

Catalog excerpts

M 30 RC - 1

1 Dosing equipment for aggressive gases Chlorination System M 30 RC is designed for direct feed of gaseous chlorine under pressure, e. g. for open swimmingpools and tanks at locations where it is not possible to provide an auxiliary power supply. The capacities of the device vary from 0 - 2000 g/h, functioning on the principle of pressure in the chlorine cylinder with manual feed rate adjustment. The M 30 RC System consists of: Pressure regulator  Diffuser  Three way valve  Accessories  Pressure principle Capacity: up to 2 kg/h For locations with no auxiliary power supply System of pressure regulators M 30 RC is equipped with a pressure reducing valve which prevents the chlorine gas to enter under high pressure. The pressure is reduced to a 1,2 bar maximum. Exhaust should be made so that the remainig chlorine gas in the pipline is neutralised. The diffuser should be mounted at least 1,2 m below water level and maximum of 7m - the higher the feed rate the greater should be the depth. Because of the influences of temperature and quality of the media, bubbles and other factors, always choose the deepest point to insure best possible absorption. OPERATION PRINCIPLE Chlorine gas under cylinder pressure enters the regulator through the inlet valve, where the pressure is reduced to 1,2 bar. The gas then flows through the rate tube and the rate valve where the desired amount is set. The set amount of chlorine gas goes through the chlorine pipe and three way valve to the diffuser, where it is mixed with water. The diffuser is equipped with check valve to prevent the water entering the system. Example of pressure regulator installation Diffuser with 2 stones

Open the catalog to page 1
M 30 RC - 2

1 Dosing equipment for aggressive gases ORDER CODES Model Regulator Gas Type Dosing range Pressure gauge Connection Yoke OPTIONS: - Regulator: yes “R”, means system with all general parts - Gas type: “C” - Cl2, “CO2” - CO2, “S” - SO2, “N” - NH3 - Dosing range (g/h): 1 up to 12 2 up to 25 3 up to 100 4 up to 200 5 up to 500 6 up to 1000 7 up to 2000 - Pressure gauge: by default—yes“M”, without it the letter is not written in the code - Yoke - standard nut; for clamp type the letter ''F'' is written in the code TECHNICAL DATA Accuracy: Within 4% of flow Operating range : 20 : 1 System Weight:...

Open the catalog to page 2

All Controlmatik catalogs and technical brochures

  1. MR 50 RC

    2 Pages

  2. MR 40 RC

    2 Pages

  3. MR 21 RC

    2 Pages

  4. MR 20 RC

    2 Pages

  5. M 470 C PVC

    2 Pages

  6. M 3800

    2 Pages

  7. M 2103 C

    2 Pages

  8. M 4510 C

    2 Pages

  9. M 5265 C

    2 Pages

  10. automation

    1 Pages

  11. M 5700 C

    2 Pages

  12. M 1322

    2 Pages

  13. M 1122

    2 Pages

  14. M 1056 C

    2 Pages

  15. M 1036 C

    2 Pages

  16. M 1035 C

    2 Pages

  17. M 20 RC

    2 Pages

  18. M 3610 C

    2 Pages

  19. M 3480 C

    2 Pages

  20. M 3100 C

    2 Pages

  21. M 3319 C

    2 Pages

  22. M 3531 C

    2 Pages

  23. M 300 C

    2 Pages

  24. M 200 C

    2 Pages

  25. M 20 C

    2 Pages

  26. M 40 C

    2 Pages

  27. M 50 C

    2 Pages

  28. M 5262 C

    2 Pages

  29. M 5600 C

    2 Pages

  30. M 3521 C

    2 Pages

  31. M 40 C

    2 Pages