SOLENOID OPERATED DIRECTIONAL VALVES 5505 WEST 123RD STREET • SAVAGE, MN 55378-1299 / PH: 952.895.6400 / WWW.CONTINENTALHYDRAULICS.COM VSD05M - SOLENOID OPERATED DIRECTIONAL VALVES CONTINENTAL HYDRAULICS

VSD05M - SOLENOID OPERATED DIRECTIONAL VALVES SOLENOID OPERATED DIRECTIONAL VALVES TYPICAL PERFORMANCE SPECIFICATIONS These valves conform to NFPA D05 and ISO 4401 mounting standards. They are available in both 3 way and 4 way styles. All versions are available in 2 position spring offset, 2 position detent, 2 position spring centered and 3 position spring centered versions. MAXIMUM OPERATING PRESSURE A wide range of spools are available. Standard and CSA approved versions are available. FLOW RATE MAXIMUM WEIGHT RANGE TEMPERATURES FLUID VISCOSITY Recommended FLUID CONTAMINATION WWW.CONTINENTALHYDRAULICS.COM...

IDENTIFICATION CODE DESIGN LETTER SOLENOIDS - See the codes on page 10 Single Solenoid 2 Position Spring Offset MECHANICAL OMIT IF NOT REQUIRED Single Solenoid Operator At ‘B’ Port End. WD Spool Type See Next Page CONNECTION BOX OPTIONS OMIT IF NOT REQUIRED ELECTRICAL OPTION OMIT Plug-in terminal solenoids or lead wires VSD05M - SOLENOID OPERATED DIRECTIONAL VALVES Connection box with terminal posts and lights 2 Dual Solenoid 2 Position Detented (No Spring) APPROVALS OMIT 3 Dual Solenoid 3 Position Spring Centered 5 Single Solenoid 2 Position Spring Centered 6 Single Solenoid 2 Position Energize...

SPOOLS CENTER POSITION FUNCTION MATCHING All ports blocked or P and A blocked and B→T All ports open, restricted P and B blocked and A→T or all ports blocked All ports open, restricted All ports open, restricted VSD05M - SOLENOID OPERATED DIRECTIONAL VALVES These are the standard configurations. Contact Continental Hydraulics for special versions.

PRESSURE DROPS ∆P-Q SHIFTED VALVE (OBTAINED WITH VISCOSITY OF 170 SUS - 36 CST AT 70°F - 21°C) P→A VSD05M - SOLENOID OPERATED DIRECTIONAL VALVES FLOW CURVE NUMBER SPOOL PRESSURE DROPS ∆P-Q CENTRAL POSITION FLOW CURVE NUMBER SPOOL P→A PERFORMANCE CURVE DC VOLTAGE [email protected] - WWW.CONTINE

PERFORMANCE CURVE VSD05M - SOLENOID OPERATED DIRECTIONAL VALVES NOTES: 1. The values indicated in the graphs are relevant to the standard valve. The DC Performance Curve used a 42L coil, the AC Performance Curve used a 60L coil, and the AC Low Force Curve used a 68L coil. 2. Valve performance was tested in a four way circuit (full loop). Performances may be reduced from that shown when used in a three-way circuit (half circuit), i.e. A or B port plugged. 3. The values have been obtained according to ISO 6403 norm with solenoids at rated temperature and supplied with voltage equal to 90% of the...

OVERALL AND MOUNTING DIMENSIONS - CONNECTION BOX VERSION VSD05M-2*, 3* VSD05M - SOLENOID OPERATED DIRECTIONAL VALVES Connection Box Manual Override Integrated in the Tube. SOL. ‘B’ Coil Removal Space Mounting surface with sealing rings: 5 pcs. AS568-014 90 Shore A Manual Override Integrated in the Tube. SOL. ‘B’ Coil Removal Space [email protected] - WWW.CONTINENTALHYDRAULI

OVERALL AND MOUNTING DIMENSIONS - DIN STYLE VERSION Coil Removal

Valves are available with an electrical connection box or with DIN 43650 solenoids in both AC and DC voltages. Deutsch DT04 or lead wires are also available in DC voltages only. VSD05M - SOLENOID OPERATED DIRECTIONAL VALVES To simplify the connections and prevent wiring mistakes, we offer the option with connection boxes with quick connect pin receptacles, already wired. Valves are available with receptacles on solenoid side ‘A’ or ‘B’ and several connector styles. Below are the codes to be included in the box ‘option’ of the ordering code, depending on the version you choose. Wiring diagrams...

SOLENOIDS VSD05M - SOLENOID OPERATED DIRECTIONAL VALVES Listed below the types of solenoids available and the numbers to be added in the solenoid box on page 3. PLUG-IN TERMINAL SOLENOID DIN 43650 This solenoid has three terminal posts. Use bi-polar connectors that meet ISO 4400 / DIN 43650 (EN 175301-803). Protection against atmospheric agent: IP 65 CONNECTION BOX SOLENOIDS This is a two pin solenoid which connects to the circuit board. Wiring is done on the terminal strip inside the box. VOLTAGE & FREQ. [VOLT - HERTZ] WASHDOWN OPTION (CODE WD) The wash-down option with the electrical box is...

APPLICATION DATA FLUID VISCOSITIES Use mineral oil-based hydraulic fluids HL or HM type, according to ISO 6743-4. For these fluids, use NBR seals. For fluids HFDR type (phosphate esters) use FPM seals (code G). For the use of other kinds of fluid such as HFA, HFB, HFC, please consult our technical department. Using fluids at temperatures higher than 180 degrees F causes the accelerated degradation of seals as well as degradation of the fluids physical and chemical properties. From a safety standpoint, temperatures above 130 degrees F are not recommended. Ambient RANGE TEMPERATURES: FLUID VISCOSITY...

VSD05M - SOLENOID OPERATED DIRECTIONAL VALVES ABOUT CONTINENTAL HYDRAULICS Rugged, durable, high-performance, efficient—the reason Continental Hydraulics’ products are used in some of the most challenging applications across the globe. With a commitment to quality customer support and innovative engineering, Continental’s pumps, valves, power units, mobile and custom products deliver what the markets demand. Continental has been serving the food production, brick and block, wood products, automotive and machine tool industries since 1962. Learn how our products survive some of the most harsh...