EIPE
4Pages

{{requestButtons}}

Catalog excerpts

EIPE - 1

SHEET EIPE Skorpion PoE Mid-Span Injector & Splitter Power over Ethernet (PoE) equipment adds power to the data in Ethernet wiring — so that devices such as surveillance and card access machines can be powered via standard Ethernet cabling. PoE Mid-span Injector PoE applications require a 48 VDC power source, but most automation systems run from 24 VAC/VDC power. If only one Ethernet-powered device (PD) needs power, the EIPE-1 can provide it. Typically the injector is inserted mid-span between a standard Ethernet switch and the PD. The EIPE-1 operates from 24 VAC/VDC to produce the required 48 VDC which it injects into the Ethernet cable to provide power and data to the PD. Under certain circumstances a non-PoE compliant device can work with the use of the EIPE-2 splitter. If the end device is 10/100 Mbps Ethernet-based but requires 24 VDC to operate, the splitter will accept the combined 48 VDC and data from a power sourcing equipment (PSE) and then generate 24 VDC to provide the end device with separate data and power. • Fully powers one Powered Device (PD) • 24 VAC/VDC power input • Isolated 15.4 W power output • 48 VDC power input • 24 VDC, 10 W power output Both Models • • • • • • • IEEE 802.af compliant Enhanced EMC compliance 10BASE-T/100BASE-TX DIN-rail mounting Rugged metal enclosure Diagnostic LEDs CE mark, UL 508 listed, c-UL EIPE-2 Splitter

Open the catalog to page 1
EIPE - 2

Data Sheet — EIPE Overview Each mid-span model has two RJ-45 connectors. The upper connector attaches to the upstream device. The lower one attaches to the end device. Transmit and receive signals pass between the two connectors as if the mid-span device were not present. Both mid-span models support the 802.3af protocol. Each has a rugged metal enclosure and metal DIN-rail clip for control panel mounting. The EIPE-1 Injector is powered from a 24 VAC/VDC source — eliminating the need and expense of the 48 VDC power supply typically associated with PoE equipment. In many industrial control...

Open the catalog to page 2
EIPE - 3

Data Sheet — EIPE Specifications Power Requirements Operating Temperature Storage Temperature Relative Humidity Protection EIPE-2 input power: 48 VDC±10% 12.95 W (via the RJ-45 port) Ethernet Communications IEEE 802.3 10/100 Mbps data rate 10BASE-T, 100BASE-TX physical layer 100 m (max) CAT5 cable length total for both cables Power Green = power OK Power over Ethernet Green = power being delivered Flashing: 1 = low signature resistance 2 = high signature resistance 5 = excessive current Off = no power being delivered 48V IN Green = acceptable input power applied 24V OUT...

Open the catalog to page 3
EIPE - 4

Data Sheet — EIPE Typical PoE Installations Ordering Information Model EIPE-1 EIPE-2 Description PoE mid-span power injector PoE mid-span power splitter United States Contemporary Control Systems, Inc. 2431 Curtiss Street Downers Grove, IL 60515 USA China Contemporary Controls (Suzhou) Co. Ltd 11 Huoju Road Science & Technology Industrial Park New District, Suzhou PR China 215009 Tel: +86 512 68095866 Fax: +86 512 68093760 info@ccontrols.com.cn www.ccontrols.asia United Kingdom Contemporary Controls Ltd 14 Bow Court Fletchworth Gate Coventry CV5 6SP United Kingdom Germany Contemporary...

Open the catalog to page 4

All Contemporary Controls GmbH catalogs and technical brochures

  1. BASgatewayLX

    12 Pages

  2. BAS Remote

    9 Pages

  3. BAS Router

    8 Pages

  4. EISX Series

    6 Pages

  5. EICP Series

    4 Pages

  6. EIMK

    4 Pages