vbOnline Pro Condition Monitoring System
12Pages

vbOnline Pro Condition Monitoring System Datasheet Bently Nevada Machinery Condition Monitoring Description The vbOnline Pro Condition Monitoring System uses sophisticated signal processing algorithms together with machinery operating states to monitor assets continuously. This system is part of a condition based maintenance program that identifies problems before assets begin to fail. Benefits of the vbOnline Pro Condition Monitoring System are: l Cost savings from reduced machinery down time l Early detection of bearing defects l Reduction of damage to assets The monitoring system's key features are: Signal conditioning Alarming Speed inputs Control system communication The vbOnline Pro Condition Monitoring System communicates with System 1, machine control systems and imports data from external Modbus sensor systems via dual Ethernet connections. The analog input channels support standard industrial accelerometers using 24 bit analog-todigital conversion over a 40 kHz bandwidth to monitor rolling element bearing machinery and all gearbox configurations. The vbOnline Pro Condition Monitoring System supports monitoring machinery that works through numerous operating states, power levels, speeds, loads or modes. Data collection can be controlled, compartmentalized and alarmed by any combination of measured parameters, including speed, vibration amplitude, individual measurement alarm status and any parameter from external source

vbOnline Pro Condition Monitoring System Datasheet Sophisticated signal processing algorithms extract measurement and health indices from each accelerometer point. The algorithms can be custom tuned to specific bearing and gear box characteristics. The vbOnline Pro Condition Monitoring System exports trended measurements like direct, bias, speed, gap as well as channel NOT OK status to third party systems such as DCS via Modbus over ethernet. The vbOnline Pro Condition Monitoring System components are the vbOnline Pro monitor, System 1, Bently Nevada Monitor Configuration software,...

vbOnline Pro Condition Monitoring System Datasheet Figure 1: vbOnline Pro Condition Monitoring System Components

vbOnline Pro Condition Monitoring System Datasheet Indicates a Danger Alarm condition Indicates an Alert condition Indicates Keyphasor signal 1 is triggering Minimum Input 18 Vdc Power Indicates Keyphasor signal 2 is triggering Maximum Input Power Indicates Network A has a valid link Indicates network traffic is flowing on Network A Specifications Electrical Specifications Inputs Maximum Current Maximum Inrush Current Indicates Network B has a valid link Maximum Inputs 12 dynamic signals 2 Keyphasor signals Indicates network traffic is flowing on Network B Dynamic Range Signal/Noise Ratio...

vbOnline Pro Condition Monitoring System Datasheet Up to once every 10 minutes User configurable Data Storage Update Rate 8 hours Typical No alarms Supported Transducers Acceleration Channels Keyphasor Signal Inputs Compatible with constant current accelerometers Proximity switches such as Turck Ni8–M18T–AP6X7M Bently Nevada Proximity Probes Speed Range Keyphasor Channels Speed Accuracy Input Frequency Auto Threshold Operating Temperature Range Supported signal range +4V to -23V. User selectable from 0.2 to 10 volts. 0% to 95% non-condensing for operation and storage Pollution Degree...

vbOnline Pro Condition Monitoring System Datasheet For the detailed listing of country and product specific approvals, refer to the Approvals Quick Reference Guide (108M1756) available from Bently.com. Standards EN 61000-6-2 Immunity for Industrial Environments EN 61000-6-4 Emissions for Industrial Environments SPECIFIC CONDITIONS OF USE: 1. The device shall be installed in an additional enclosure that provides an ingress protection rating not less than IP54 and meets the enclosure requirements of IEC 60079-0. 2. The equipment shall only be used in an area of not more than pollution degree...

vbOnline Pro Condition Monitoring System Datasheet Part Number Ordering Information Accelerometer Mounting Stud 1/4 -28 to M8x1.25 SST Accelerometer Cable 15.2 m (50 ft) with straight connector Accelerometer Cable 9.1 m (30 ft) with straight connector Accelerometer Cable 15.2 m (50 ft) with right angle connector For the detailed listing of country and product specific approvals, refer to the Approvals Quick Reference Guide (108M1756) available from Bently.com. Accelerometer Cable 9.1 m (30ft) with right angle connector None Multi Approvals (CSA, IECEx, ATEX) Sensors and Cables Part Number...

vbOnline Pro Condition Monitoring System Datasheet Accessories Bently Nevada Monitor Configuration Software DVD 100M9465-01 BNMC Software is included with vbOnline Pro Condition Monitoring System for user administration, IP configuration and firmware updates. Spare Power Input Connector Spare Input Connector Ch 110 Spare Input Connector Ch 1112 Spare Input Connector KPH 1-2

vbOnline Pro Condition Monitoring System Datasheet Graphs and Figures Dimensions shown are in inches (millimeters)

vbOnline Pro Condition Monitoring System Datasheet Figure 2: vbOnline Pro - Side View Figure 3: vbOnline Pro - Top and Bottom Views

vbOnline Pro Condition Monitoring System Datasheet Figure 4: Recommended Minimum Clearance Window for Cable Terminations and Monitor Cooling

vbOnline Pro Condition Monitoring System Datasheet Copyright 2021 Baker Hughes Company. All rights reserved. Bently Nevada, Keyphasor, System 1, vbOnline and Orbit Logo are registered trademarks of Bently Nevada, a Baker Hughes Business, in the United States and other countries. The Baker Hughes logo is a trademark of Baker Hughes Company. All other product and company names are trademarks of their respective holders. Use of the trademarks does not imply any affiliation with or endorsement by the respective holders. Baker Hughes provides this information on an “as is” basis for general...