Catalogs >
Conbraco Industries >
cat_PHBRHYD

cat_PHBRHYD
40Pages

Catalog excerpts

HYDRONIC & STEAM HEATING PRODUCTS

Quality, Service Now in its ninth decade, Conbraco Industries, Inc. is a leading manufacturer of flow control products for U.S. and international markets. The company's headquarters is based in Matthews, North Carolina with manufacturing plants and foundries located in Pageland and Conway, South Carolina. Conbraco has a history of new product development and innovation that dates back to the company's inception in 1928. Today, the Conbraco line of products is marketed under the "Apollo Valves" brand and includes: ball valves, butterfly valves, backflow prevention devices, water pressure...

Open the catalog to page 2

HYDRONIC & STEAM HEATING PRODUCTS A Bronze Body Feed Water Regulator – 35-703-01 (FFS12) B ASME Section IV Water Boiler Safety Relief Valve – 10-102-05 (RVW10F) C Pressure Relief Valve (Tankless Coil) – 17-401-04 (RVW1712150) D Thermostatic Mixing Valve – 34A-200(MVA) E Flow Control Valve (Tankless Coil) – 35-403-01 (FCT12) F Backflow Preventer – 40-4A3-3AM (DCAP12) G Purge/Balancing Valve – 78-668-01 (PBSS34) H Boiler Drain Valve – 31-202-04 (BD9034) 4 I Bronze Check Valve – 61 Series (CVB) J Apollo® Ball Valve – 70 Series K Apollo® Ball Valve – Stop and Drain 95-204-01 L Hydronic...

Open the catalog to page 4

HYDRONIC HEATING PRODUCTS Handles supply pressures up to 400 psig; working temperatures to 180°F. All-bronze body, corrosion resistant cage, stainless steel strainer and seat. Meets ASSE and CSA standards; listed with IAPMO. FDA approved EPDM diaphragm Standard factory setting: 50 psi Adjusts from 25 to 75 psi (standard) Designed to meet local plumbing codes High and low pressure options Balanced piston design Stainless steel adjusting screw and nut Sealed cage Pipe union, meter union, female NPT, CPVC, Pex or solder-joint connection Internal thermal expansion by-pass Model 36CLF Lead Free...

Open the catalog to page 5

HYDRONIC HEATING PRODUCTS Hydronic Heating Specialties ALL BRONZE FEED WATER PRESSURE REGULATORS Available in 1/2"union threaded, threaded and solder union configurations. Purge lever/fast fill feature. Cartridge replaceable in-line. No cage screws to rust Individually set at 15 psig - Adjustable Heavy pattern bronze body and spring cover High capacity SS strainer, in-line, standard Choice of inlet connections ALL BRONZE COMBINATION DCAP BACKFLOW PREVENTER AND FEED WATER REGULATORS Positive protection against backflow when supply pressure falls below system pressure. Assembly combines FWR...

Open the catalog to page 6

HYDRONIC HEATING PRODUCTS Protects residential and commercial water supply lines from back-siphonage or back-pressure of non-potable substances. Suitable for hot or cold water service. Low head loss. Approved by ASSE & CSA • Durable Maximum working pressure: 175 psig • Easy to install, maintain and repair Independently acting check valves • Operating temperature: 33"F to 210"F Sizes 1/2"and 3/4" • Designed, manufactured, assembled and Corrosion resistant tested in South Carolina, USA PART NUMBER: INLET CONNECTION MODEL NUMBER: INLET CONNECTION B-Female BSPP OUTLET CONNECTION S-Female BSPP...

Open the catalog to page 7

HYDRONIC HEATING PRODUCTS Reduced Pressure Principle Devices I BRONZE REDUCED PRESSURE PRINCIPLE BACKFLOW PREVENTER Designed to give maximum protection against backflow caused by either back-pressure or back- siphonage.The durable, but economical, device is easily maintained in the line without any special tools. It consists of two independently acting spring-loaded check valves with an automatic differential relief valve located between the check valves. The diaphragm and the sensing passage are built into the all bronze body to eliminate possible damage. Three of the test cocks are...

Open the catalog to page 8

HYDRONIC HEATING PRODUCTS For installation with Conbraco's RP-40 Series Reduced Pressure Principle backflow preventers. The Apollo Air Gap Drain (AGD) is designed to funnel minor relief valve discharges, due to line pressure fluctuations and /or minor check valve fouling, into the drainage system. Drain piping is easily attached to the drain's threaded bottom. Note: The AGD is NOT designed to collect the full discharge capacity of the relief valve. * TheAGD40 Air Gap Drains are manufactured in the USA of lightweight ABS plastic. The versatile ABS plastic allows drainage piping to be...

Open the catalog to page 9

HYDRONIC HEATING PRODUCTS Hydronic Heating Specialties MULTI-ORIFICE CONTROL VALVE Provides flow control on tankless heaters; for delivery of 2-1/2,3,3-1/2, and 4 GPM. Easy adjustment. Maximum pressure: 150 psig ALL BRONZE HYDRONIC FLOW CHECK VALVES The flow check is designed to provide positive shut-off when water service is interrupted. Corrosion resistant • Designed for easy maintenance Wear resistant metal to metal seat • Suitable for hot or cold water service Replaceable seat assembly • Maximum working pressure 50 psi. for By-pass option 3/4"-1-1/4" 125 psig for 1-1/2"- 2" Sweat or...

Open the catalog to page 10

HYDRONIC HEATING PRODUCTS Hydronic Heating Specialties MODEL PBSS BRONZE PURGE, BALANCE & SHUT-OFF VALVE Straight-through flow; all brass cover and chain prevent accidental system drainage; hose thread connection for disposal of drained media. • RPTFE seals • 600 Psig CWP in open position Adjustable packing • Solder x Solder x Hose Connections Zinc plated steel tee handle w/vinyl grips * Available with screwdriver slotted stainless steel stem. EXPANSION TANKS FOR HYDRONIC SYSTEMS Conbraco non-potable expansion tanks help maintain balanced pressure throughout a hot water heating system by...

Open the catalog to page 11

HYDRONIC HEATING PRODUCTS AS ME Section IV Hot Water Relief Valves ISECTION IV ASME HOT WATER RELIEF VALVES MODEL NUMBER: C-satin chrome PRESSURE SETTING These capacity-certified relief valves protect against excessive water pressure (from thermal expansion) and steam generated when Btu input controls fail. Valves comply with ASME Section IV requirements. Ideal for use with hot water boilers and heating systems. Brass or bronze body available with optional satin or polished chrome finish Maximum temperature service: 250°F Registered in all Canadian provinces Stainless steel springs standard...

Open the catalog to page 12