BUTTERFLY VALVES R E S I L I E N T S E AT E D & DOUBLE OFFSET HIGH PERFORMANCE

Conbraco Industries, Inc. is a leading manufacturer of flow control products for U.S. and international markets. The company’s headquarters is based in Matthews, North Carolina with manufacturing plants and foundries located in Pageland and Conway, South Carolina. Apollo® and Apollo InternationalTM iron bodied butterfly valves offer an economical, bubble-tight shut-off design that’s ideal for use in commercial HVAC and plumbing as well as irrigation and select industrial applications. These valves are rated to 200 psig in sizes 2” through 12” and 150 psig in sizes 14” and larger. Apollo® and...

BUTTERFLY VALVES - RESILIENT SEATED general purpose butterfly valves - 141 & 145 series Ductile Iron ASTM A536 (65-45-12) EPDM* --- or --Buna-N (Nitrile)* --- or --Viton®B* 416 Stainless Steel ASTM A564 Nickel Plated Ductile Iron ASTM A536 (65-45-12) --- or --Aluminum-Bronze ASTM B148, C95400 --- or --316 Stainless Steel A STM A351, Type CF8M Bushing Weather Seal Retainer Washer Set Screws (Flat Point) Set Screws (Cone Point) Steel with Protective Finish Steel with Protective Finish Steel with Protective Finish Steel with Protective Finish Glass Reinforced Epoxy 5 AVAILABLE OPTIONS • 10 Position...

BUTTERFLY VALVES - RESILIENT SEATED specifications - 141 & 145 series DESIGN SPECIFICATIONS £ WD (ductile iron, wafer body design) LD (ductile iron, single flange, lug body design) SIZE RANGE 141 Series: Apollo InternationalTM WD141 (wafer body design): 2”-12” (DN50 - DN300) LD141 (single flange body design): 2”-24” (DN50 - DN600) £ Designed to fully comply with MSS SP-25, MSS SP-67, and API 609 £ Meets the intent and passed AWWA C-504 Section 5* proof of design tests £ NSF/ANSI 372 “lead free” in compliance with the U.S. Safe Drinking Water Act effective January 4, 2014. £ Extended neck to allow...

BUTTERFLY VALVES - RESILIENT SEATED options The following options are available factory installed on any of the LD or WD Series Apollo Butterfly Valves. The LC149 series are available either with the standard 10-position handle or with the optional gear operator on sizes 8” and larger. The other options may be purchased in kit form and installed by the user or distributor. BARE STEM (MODEL CODE SUFFIX 0) Select this suffix to specify a butterfly valve without a handle, gear operator or actuator. TEN (10) POSITION HANDLE (SUFFIX 1) The 10 position handle is the most common manual operator for...

BUTTERFLY VALVES - RESILIENT SEATED applications The Apollo® LD/WD Series Ductile Iron Butterfly Valves offer reliable performance in a wide range of applications; on/off, throttling, control isolation, flow balancing and diversion. Ideal for use in Industrial and HVAC/Mechanical applications. Service compatibility is dependant on several factors; the corrosion resistance of the disc and shaft and the chemical resistance of the seat (liner) and required temperature range. Erosion resistance also affects material selection when dealing with abrasive slurries. EPDM Cartridge Style Seat Ethylene...

BUTTERFLY VALVES - RESILIENT SEATED installation Apollo® butterfly valves are designed for installation between ANSI Class 125/150 lb. weld-neck or slip-on flanges. While we suggest use of weld neck flanges, Apollo® models are configured to also accept slip-on flanges that eliminate failures associated with conventional butterfly valves. Be sure to properly align flange and valve when using raised face flanges. Type C stub end flanges are not recommended. Apollo butterfly valves can be used with schedule 40 and schedule 80 steel pipe. When the valve is properly centered between flanges, the disc...

BUTTERFLY VALVES - RESILIENT SEATED general purpose butterfly valves - 141 & 145 series WD MODEL 141 Series: Apollo InternationalTM 145 Series: Assembled & Tested in USA Double-D Shaft Drive Double-D Shaft Drive Shaft Drive: Double-D (14”) Round & Keyed (16” & larger)

BUTTERFLY VALVES - RESILIENT SEATED general purpose butterfly valves - 141 & 145 series DOUBLE-D AND KEYED STEM Dimensions in Inches Size Inches Approximate Weight for Bare Shaft Valve For additional information, submittal sheets and manuals, visit www.apollovalves.com 141 Series: Apollo InternationalTM 145 Series: Assembled & Tested in USA * keys are supplied w/ bare stem v

BUTTERFLY VALVES - RESILIENT SEATED handle & gear dimensions - 141 & 145 series 141 Series: Apollo InternationalTM 145 Series: Assembled & Tested in USA with Manual Gear with Manual Gear with Handle

BUTTERFLY VALVES - RESILIENT SEATED operating torque - 141, 145 & 149 series All torque valves shown in the chart are for wet (water and other non-lubricating media) on-off service. For dry services (nonlubricating, dry gas media) multiply the values by 1.15. For lubricous services (clean, non-abrasive lubricating media) multiply values by 0.85. Torque Rating (lbs•in) Under certain conditions, hydrodynamic torque can meet or exceed seating and unseating torques. When designing valve systems, hydrodynamic torque must be considered to help ensure correct selection of actuation. Velocity Limits...

BUTTERFLY VALVES - RESILIENT SEATED contractor grade butterfly valves - 149 series The Apollo® LC149 Series Cast Iron Butterfly Valves are ideal for use in Industrial and HVAC/Mechanical applications. The LC149 Series is a lug style valve designed to be economical yet full featured. STANDARD MATERIALS Body Cast Iron, ASTM A126 Class B Disc Aluminum Bronze, ASTM B148-C95400 Shaft Stainless Steel, ASTM A276, Type 416 Seat Black EPDM (FDA food grade) with phenolic backing Bushings PTFE Stem Seal EPDM PERFORMANCE RATING • Max Operating Pressure: 200 psi (13.8 bar) • Temperature Range: -20°F to 250°F...

BUTTERFLY VALVES - RESILIENT SEATED how to order WD and LD butterfly valves CERTIFIED LEAD FREE NSF/ANSI 372 – MODEL NUMBER WD MODEL SERIES LD = Lug Body (Ductile Iron) 141 = Apollo InternationalTM WD = Wafer Body (Ductile Iron) 145 = Assembled & Tested in USA (2” - 12” Only) SIZE (IN.) DISC MATERIAL SEAT MATERIAL SHAFT OPERATOR 02 = 2” B = Aluminum Bronze E = Black EPDM** 1= Std. 0 = Bare Shaft 25 = 2.5” D = Ductile Iron A536 -20° F to 250° F 416 SS 1 = 10 Position Handle 03 = 3” Nickel Plated Intermittent 2 = Gear Operator - Direct Mount 04 = 4” S = Stainless Steel, CF8M 225° F - Continuous...