video corpo

TrueWeigh Hopper
2Pages

{{requestButtons}}

Catalog excerpts

TrueWeigh Hopper - 1

EXTRUSION CONTROL PRECISE MEASUREMENT OF MATERIAL THROUGHPUT Engineered as part of the Conair TrueWeigh Gravimetric Extrusion Control System, the TrueWeigh hopper measures the mass flow of material into the extrusion process and sends this loss-inweight information to the TrueWeigh controller. The controller then accurately monitors or adjusts the extruder screw RPM and/or haul-off RPM to maintain a consistent yield control. This enables an operator to run a uniform product within the tightest tolerances at the lowest possible cost. ACCURATELY MEASURES EXTRUDER RATE BY WEIGHT Mounting directly to the extruder throat, the TrueWeigh hopper includes the weigh electronics and load cell required to precisely measure the extruder’s material throughput. The “floating” weigh hopper is cantilevered off the load cell and is contained within a heavy-duty frame. Three (3) hopper sizes are available for throughput rates from 10 to 5,000 lbs/hr {4.5 to 2268 kg/hr}. The hoppers include a 60 degree bottom cone for constant plug flow to optimize blend integrity through the weigh hopper. The steep wall hopper works well with any combination of free-flowing pellet, flake, regrind and free-flowing powder or granular materials. A clear polycarbonate inspection/clean-out door or sight glass allows at-a-glance visual inspection of the hopper contents. Ease of installation TrueWeigh hoppers are supplied with sub-plates for direct connection to the extruder feed throat. Supplied as a blank, the sub-plate eliminates the need for feed throat detailing prior to installation. Simply measure and drill the matching feed throat bolt pattern, fasten the sub-plate in place and mount the hopper. No additional support is needed. Optional custom mounting adaptors are also available. Integral loading support platform TrueWeigh standard loading options accommodate Conair positive slide gates with vacuum receivers, surge hoppers, stub, or blending systems. Custom adapters are available to accommodate non-Conair loading equipment. TrueBlend integration The TrueWeigh hopper can be used in conjunction with a TrueBlend Gravimetric Batch Blending System. The largest hopper can support up to a TB900 with loaders with no additional support requi

Open the catalog to page 1
TrueWeigh Hopper - 2

EXTRUSION CONTROL Side view Front view ■ Mild steel construction ■ High accuracy, precision cantilever load cell ■ High resolution weighing electronics ■ Integral loader/surge hopper support platform for Bottom plate Note: Standard plate is supplied blank MODEL Performance characteristics Hopper capacity ft3 {l} Dimensions inches {mm} A - Height B - Depth C - Hopper width D - Overall width E - Mounting plate width F - Hole diameter G - Hole diameter H - Hole diameter J - Hole diameter Approximate weight lb {kg} Shipping Extruder size inches {mm} Minimum Maximum Conair equipment ■ Inspection...

Open the catalog to page 2

All Conair catalogs and technical brochures

  1. 5000 Blender

    4 Pages

  2. MedLine

    4 Pages

  3. TrueRate™

    3 Pages

  4. TrueWeigh

    6 Pages

  5. INTERMIXER

    2 Pages

  6. Dump Table

    2 Pages

  7. CPC Series

    4 Pages

  8. Medline

    6 Pages

  9. MEDVAC TANKS

    4 Pages

  10. HTR series

    4 Pages

  11. VTR

    4 Pages

  12. TW-V

    4 Pages

  13. TW-S

    4 Pages

  14. TW-P

    4 Pages

  15. TAC series

    2 Pages

  16. WELDED SILOS

    2 Pages

  17. HTMP SERIES

    4 Pages

  18. PTFG

    4 Pages

  19. CFC series

    2 Pages

  20. EP2

    8 Pages

  21. PTSS 0450

    4 Pages

  22. EP1

    6 Pages

  23. FLX-128

    4 Pages

  24. Bolted Silos

    2 Pages

  25. CH Hoppers

    4 Pages