Pneumatic and Hydraulic Gate Valve Actuators
18Pages

Pneumatic and Hydraulic Gate Valve Cylinders through 24 inch bore

www.compactautomation.com • Customer Service: 864-647-9521 • Email: CAP_CustomerService@itt.com

Pneumatic Gate Valve Cylinders Overview Valve Actuator markets are typically: • • • • Oil & Gas Power Gen Pulp and Paper Water Aluminum Components – 2-1/2” through 12” Bore The end plates and piston are made from high strength Aluminum. Combined with an Aluminum or composite cylinder tube the ITT GV actuators are over 50% lighter than actuators constructed from steel components. The end plates are black hard coat anodized for high corrosion and abrasion resistance. End plates with rounded corners All end plates have rounded versus sharp corners to minimize the potential for injury when...

Pneumatic Gate Valve Cylinders - 2-1/2" to 24" Bore ALUMINUM HEAD CAP AND REAR CAP ALUMINUM TUBE COMPOSITE TUBE AND WEAR STRIP WITH *Alternate materials of construction are available for services where aluminum or steel is not compatible. TEMPERATURE RATINGS Standard Materials Buna-N seals and aluminum tube (2.5-5 in. bores): -20°F - 220°F (-29°C - 104°C) Buna-N seals and composite tube (6-24 in. bores): -20°F - 220°F (-29°C - 104°C) Optional Materials Buna-N seals and steel tube (all bore sizes): -20°F - 220°F (-29°C - 104°C) Fluorocarbon and aluminum tube (2.5-5 in. bores): -15°F - 400°F...

Pneumatic Gate Valve Cylinders How to Order ROD MATERIAL SEAL MATERIAL Rod Style Single (Leave Blank) Double Rod (Standard Model) 2-1/2” Bore Cylinder 3-1/4” Bore Cylinder 4” Bore Cylinder 5” Bore Cylinder 6” Bore Cylinder 7” Bore Cylinder 8” Bore Cylinder 10” Bore Cylinder 12” Bore Cylinder 14” Bore Cylinder 16” Bore Cylinder 18” Bore Cylinder 20” Bore Cylinder 22” Bore Cylinder 24” Bore Cylinder Stroke Indicate in Inches - Two Decimal Places Leave Blank for Standard Dimension (See chart on pages 4-6)Indicate in Inches - Two Decimal Places CR1050 Steel (Leave Blank) CR Stainless Steel...

Pneumatic Gate Valve Cylinders - 2 1/2” to 5” Bore Technical Data THEORETICAL EXTEND FORCE LBS. (N) BORE in. (mm) THEORETICAL RETRACT FORCE LBS. (N) ROD DIA. in. (mm) WEIGHT AT ZERO STROKE LBS. (kgs.) WEIGHT PER INCH (mm) OF GV ACTUATOR LBS. (kgs.) APPROXIMATE WEIGHT* (GV WITH ALUMINUM HEADS & ALUMINUM TUBE) 2.5 (63.5) *Total cylinder weight lbs. (kgs.) = A + (B x stroke) www.compactautomation.com • Customer Service: 864-647-9521 • Email: CAP_CustomerService@itt.com

Pneumatic Gate Valve Cylinders - 6” to 12” Bore Technical Data THEORETICAL EXTEND FORCE LBS. (N) BORE in. (mm) THEORETICAL RETRACT FORCE LBS. (N) ROD DIA. in. (mm) WEIGHT AT ZERO STROKE LBS. (kgs.) WEIGHT PER INCH (mm) OF GV ACTUATOR LBS. (kgs.) APPROXIMATE WEIGHT* (GV WITH ALUMINUM HEADS & COMPOSITE TUBE) 6 (152.4) *Total cylinder weight lbs. (kgs.) = A + (B x stroke) www.compactautomation.com • Customer Service: 864-647-9521 • Email: CAP_CustomerService@itt.com

Pneumatic Gate Valve Cylinders - 14” to 24” Bore Technical Data THEORETICAL RETRACT FORCE LBS. (N) ROD DIA. in. (mm) WEIGHT AT ZERO STROKE LBS. (kgs.) WEIGHT PER INCH (mm) OF GV ACTUATOR LBS. (kgs.) *Total cylinder weight lbs. (kgs.) = A + (B x stroke) www.compactautomation.com • Customer Service: 864-647-9521 • Email: CAP_CustomerService@itt.com

Pneumatic Gate Valve Cylinders Components, Assembly and Maintenance CAUTION: CHECK MAXIMUM OPERATING PRESSURE LISTED ON CYLINDER LABEL BEFORE APPLYING PRESSURE TO CYLINDER. EXCEEDING THE PRESSURE RATING LISTED ON THE CYLINDER MAY CAUSE FAILURE WHICH MAY ENDANGER PERSONNEL AND/OR EQUIPMENT. WARNING: READ INSTALLATION SERVICE INSTRUCTIONS AND GENERAL PARTS BREAKDOWN BEFORE INSTALLATION, OPERATION OR SERVICING. THIS MANUAL IS NOT FOR SPRING LOADED CYLINDERS. NOTICE: DISASSEMBLY OF THIS PRODUCT WILL VOID WARRANTY GV ACTUATOR INSTALLATION AND MAINTENANCE INSTRUCTIONS 1. GENERAL: The parts...

Pneumatic Gate Valve Cylinders Components, Assembly and Maintenance Gate Valve Cylinder Tie Rod Torque Reference TUBE MATERIAL Aluminum lb-ft (Nm) Component Actuator Parts 1. Head Cap 2. Rear Cap 3. Tube 4. Tie Rods 5. Tie Rod Nuts 6. Tie Rod Washers 7. Piston 8. Piston Rod 9. Piston to Rod Screw 10. Piston to Rod Washer 11. Rod Bearing 12. Retaining Ring Seals 13. Tube Seals 14. Piston Seals 15. Rod Seal 16. Rod Wiper 17. Rod Bearing O-Ring 18. Piston Wear Strip 19. Wear Strip O-Ring Expanders Gate Valve Cylinder Repair Kits CYLINDER BORE SEAL MATERIAL BUNA-N REPAIR KITS CONTAIN THE...

Pneumatic Gate Valve Cylinders Options and Specials At ITT we produce the following custom options and specials: - Spring Extend - Air Retract - Spring Retract - Air Extend - Steel Tubes - Adjustable Stops - Special Coatings - Special Mountings - All Stainless Steel Components - Multi-Piston for: • Multi-Power • Multi-Position - Special Ports - Oversized Rods - Custom Rod Configurations If you can imagine a design, ITT can provide the solution. www.compactautomation.com • Customer Service: 864-647-9521 • Email: CAP_CustomerService@itt.com

Hydraulic Gate Valve Cylinders - 1-1/2" to 8" Bore 100.000 PSI MINIMUM YIELD ALLOY STEEL HARD CHRQME PLATED GROUND AND POUSHED FOR OPTIMUM SEAL LIFE FROM 100,000 PSI MINIMUM YIELD ALLOY STEEL ROLLED THREADS FOR GREATER STRENGTH HEX NUTS ARE GRADE 8 ALLOY STEEL BOTH ARE ZINC PLATED FOR CORROSION STEEL WITH HONED ID DUCTILE CAST IRON U-CUP PISTOL SEALS (2) NYLON BACK-UP ORINGS (2] MACHINED FROM ALLOY STEEL PRECISELY MACHINED ORING AND TUBE GROOVE PROVIDES SECURE ATTACHMENT TO TUBE UNRESTRICTED FLOW CHANGED BY ROTATING EITHER 2.5" BORE AND SMALLER 3.25" BORE AND LARGER MOUNTING FLANGE MACHINED...

Hydraulic Gate Valve Cylinders How to Order TYPE PRESSURE SERIES SEAL MATERIAL PORT OPTION Part Number Example: H 3 G V 1 5 x 1 . 7 5 - M F 5 - W 3 . 0 0 - F 1 Rod End Style Standard Style 4-Short Female (Leave Blank) Style 2 - Small Male Style 5 - Intermediate Male Series Gate Valve Series Rod Diameter Standard Rod Diamter *(Leave Blank) Ex. 1.38 = 1-3/8” Rod Diameter Consult Factory for Available Sizes 1-1/2” Bore Cylinder 2” Bore Cylinder 2-1/2” Bore Cylinder 3-1/4” Bore Cylinder 4” Bore Cylinder 5” Bore Cylinder 6” Bore Cylinder 8” Bore Cylinder Optional Rod Extension - Inches Two...