Microwave
6Pages

{{requestButtons}}

Catalog excerpts

Microwave - 1

Comber Process Technology S.r.l. Tel.: + 39 02 99990146 Fax: + 39 02 99990148 info@comber.it Via Garibaldi 67 I - 20061 Carugate (MI) www.comber.it Supplemental Microwave Heating Substantially reduced drying times Equal drying throughout Ideally suited for agglomerating, sticky products Accurately controlled drying process TI 0232 E - 05/08

Open the catalog to page 1
Microwave - 2

Comber Process Technology S.r.l. Tel.: + 39 02 99990146 Fax: + 39 02 99990148 info@comber.it Via Garibaldi 67 I - 20061 Carugate (MI) www.comber.it Microwave Heating Microwave Duty Preparation Preparation of a filter-dryer or dryer vessel for the installation of microwave heating entails sealing the vessel to prevent microwave leakage, the addition of nozzles for the feed of the microwaves into the vessel plus the installation of required sensors. General Design Criteria All nozzles and seals will be designed to contain the microwaves and avoid microwave leakage. Flanges will be of metal to...

Open the catalog to page 2
Microwave - 3

Comber Process Technology S.r.l. Tel.: + 39 02 99990146 Fax: + 39 02 99990148 info@comber.it Via Garibaldi 67 I - 20061 Carugate (MI) www.comber.it Microwave Heating Flange design for microwave feed To feed the microwaves through the rectangular waveguides into the filterdryer. A quartz sight glass isolates the vessel interior from the purged wave guide. 6 kW microwave generator for outdoors installation 6 kW 2.45 GHz water cooled Magnetron, with tuner and interface for PLC control system. TI 0183 E - 06/05

Open the catalog to page 3
Microwave - 4

Comber Process Technology S.r.l. Tel.: + 39 02 99990146 Fax: + 39 02 99990148 Via Garibaldi 67 I - 20061 Carugate (MI) info@comber.it www.comber.it Microwave Heating Flange design A flange design to assure a defined flange seat pressure for good metal to metal contact is used throughout the design to prevent microwave leakage. Choke Main flange chokes On the main vessel flanges where a defined flange seat pressure cannot be assured ¼ wavelength chokes are used to cancel out any microwave and thus to prevent microwave leakage Sight glass with metal screen to prevent microwave leakage. TI...

Open the catalog to page 4
Microwave - 5

Comber Process Technology S.r.l. Tel.: + 39 02 99990146 Fax: + 39 02 99990148 info@comber.it Via Garibaldi 67 I - 20061 Carugate (MI) www.comber.it Microwave Heating Glow sensor installation The glow sensor is used to detect the onset of glow (UV radiation) in order to reduce microwave power before any sparking can occur. Infrared sensor installation An infrared sensor is used to measure the product surface temperature and adjust microwave energy in order to maximize efficiency and at the same time to prevent “frying” the product Color camera and vessel light installation TI 0181 E - 06/05

Open the catalog to page 5
Microwave - 6

Comber Process Technology S.r.l. Tel.: + 39 02 99990146 Fax: + 39 02 99990148 info@comber.it Via Garibaldi 67 I - 20061 Carugate (MI) www.comber.it Pressofiltro® PF 200 Pilot Filter Dryer PF 200 pilot filter dryer with all electric actuation for a pharma-ceutical application. With connecting flange for an isolator (isolator supplied by third party) to permit sampling, dust containment during discharge, heel removal and filter cloth disposal. The pilot filter dryer is prepared for microwave duty to further reduce drying times (picture at left shows a microwave generator installed for...

Open the catalog to page 6

All Comber Process Technology Srl catalogs and technical brochures

  1. Controls

    6 Pages

  2. Heel Removal

    6 Pages

  3. Peripherals

    11 Pages

  4. Containment

    6 Pages

  5. Termomix

    10 Pages

  6. Turbodry®

    8 Pages

  7. Condry®

    8 Pages

  8. Pharmadry®

    12 Pages