RIG04 - RIG06 - RIG09
32Pages

GLOBOIDAL CAM INDEXING TABLES  Compact-size aluminium housing.  Large-diameter output plate with flange coupling.  Output plate supported by a crossed roller bearing with high load capacities.  Output configuration with central through hole and ceiling mounting.  Direct keying onboard of the motorisation box with worm screw reduction gear and friction torque limiter incorporated in the reduction gear.  Nitrided steel cam.  Possibility to assemble in all positions.  Long-life lubrication. http://www.cofil.com - E-mail: cofil@cofil.com Via G. Rossini 26 - 24040 Casirate D’Adda Bg IT Phone +39 0363 3

The units of measure comply with the SI international metric index General manufacturing tolerances comply with standard UNI – ISO 2768-1 UNI EN 22768-1 Illustrations and drawings according to 3970 (ISO 128-82) The drawings are represented with the traditional method Colombo Filippetti SpA reserves itself the right to make changes, at any time, for the purpose of improving its products. Therefore, the data contained in this catalogue are not binding. This catalogue supersedes all earlier versions. It is prohibited to reproduce, even in partial form, the content and the illustrations...

5 Table sizing - Sample applications 6-7 Configurations and variants chart Technical characteristics 8 Configuration with reduction gear and self-braking motor (VLRA) 9 Configuration with short input shaft (VS) 10 Optional configurations of the output plate 11 Optional configuration for ceiling or upside down mounting Optional reference holes RIG06 Technical characteristics 12 Configuration with reduction gear and self-braking motor (VLRA) 13 Configuration with short input shaft (VS) 14 Optional configurations of the output plate 15 Optional configuration for ceiling or upside down...

RIG04 RIG06 RIG09 GLOBOIDAL CAM INDEXING TABLES General RIGIDIAL tables are globoidal cam indexing tables that transform continuous rotary motion into indexing motion. The indexing plate rests on a large-diameter crossed roller bearing that can withstand high axial and tilting loads while maintaining excellent levels of accuracy and rigidity. The cam is nitrided and assures high wear resistance, smooth running, accurate and repeatable positioning without any backlash at the station. A wide range of standard movements is available, including the 2-station movement (180° rotation), which is...

RIG04 RIG06 RIG09 GLOBOIDAL CAM INDEXING TABLES Sizing of the table The rotary table is sized starting from a calculation of the torque required at the output. This torque has to take into account the inertia of the customer’s application, the moment of friction, and the torques due to external, static or dynamic forces requested at the output. For the purpose of avoiding vibrations during rotation, it is important to evaluate the ratio of the equivalent ratio of inertia to the pitch radius of the table cam followers. It is also important to use the proper service factor when sizing the...

RIG04 RIG06 RIG09 CONFIGURATIONS AND VARIANTS DIAGRAM VCT VCP VCM STANDARD RING RING FOR CEILING OR INVERTED MOUNTING MIB PHASE CAM with P.N.P. n.o. sensors Diagram of configuration and variants.

STANDARD CONFIGURATION • Nitrided cam. • Table centre with cover seal (VCS version). • Crossed roller bearing ring. • Universal mounting. • Worm reduction gear with torque limiter and selfbraking motor (see table on page 24). • MIB or CM4 type cam assembly with double phase switch for consent operation. ACCESSORIES AND VARIANTS • Cam with hardened and ground profile. • Reversed direction pertaining to the rotation of the motion input shaft-output plate. • Output version normal fixed central through hole without fixing holes (VCT version). • Output version with large fixed central through...

RIG04 RIG04 - CONFIGURATION WITH REDUCTION GEAR AND SELF-BRAKING MOTOR (VLRA) 27 kg 59 lbs VLRA Version. REDUCTION GEAR: RMI 40F1-PAMB14 - LCB MOTOR: SELF-BRAKING The 6 holes M6x15 on the output plate are in the position shown in Fig. 5 and 6 when the table is in the dwell period at one of the stations. The input shaft notches are in the position shown in Fig. 7 when the table is halfway through its dwell period. Some combinations of motors and reduction gears limit the performance of the tables. Standard direction of rotation (right helix of the cam) as indicated by the arrows. The pin...

RIG04 - CONFIGURATION WITH SHORT INPUT SHAFT (VS)

RIG04 RIG04 - OPTIONAL CONFIGURATIONS OF THE OUTPUT PLATE Central fixed through hub, without fixing holes. Large central fixed through hub, without fixing holes. Central fixed through hub, Ø16H8, projection Ø 42x20 and fixing holes with c

RIG04 RIG04 - OPTIONAL CONFIGURATION FOR CEILING OR INVERTED MOUNTING Configuration for ceiling or upside down mounting VC...S. RIG04 - OPTIONAL REFERENCE HOLES Three dowel holes can be drilled in the output plate and in the table feet, as indicated in Fig. 12. The purpose of the hole in the output plate is to guarantee precise and repeatable assembly of the equipment. The two holes in the feet, on the other hand, allow precise positioning and make the table interchangeable. Fig. 12 Reference holes.

RIG06RIG06 - CONFIGURATION WITH REDUCTION GEAR AND SELF-BRAKING MOTOR (VLRA) (/>??? E-CAM OUTPUT AXIS • By reversing the direction of rotation of the input shaft, the direction of rotation of the output shaft is reversed, while the kinematic characteristics of the intermittent motion in standard mechanisms remain unchanged. • The 6 holes M8x19 on the output plate are in the position shown in Fig. 13 and 14 when the table is in the dwell period at one of the stations. • The input shaft notches are in the position shown in Fig. 15 when the table is halfway through its dwell period. •...

RIG06 - CONFIGURATION WITH SHORT INPUT SHAFT (VS) No.5 M6x9 0238±O.1

RIG06 RIG06 - OPTIONAL CONFIGURATIONS OF THE OUTPUT PLATE Central fixed through hub, without fixing holes. Large central fixed through hub, without fixing holes. Central through hub Ø19H8, projection Ø50x28 and fixing holes with ce