video corpo

Parallel indexing drives 65P.80P.105P.130P
12Pages

{{requestButtons}}

Catalog excerpts

Parallel indexing drives 65P.80P.105P.130P - 1

PARALLEL INDEXING DRIVES 65P-80P-105P-130P Prism-shaped sealed cast iron housing Outer surfaces machined, with support on 6 sides. Possibility of mounting housing in all positions. Parallel shafts projecting in input and output. Roller bearings on opposite taper roller shafts. Oil-bath lubrication. Worm gear reducer splined directly to housing. Precise repeatable index motion. Self locking in dwell and zero backlash. Smooth and shock-free movement Bidirectional sense of motion. http://www.cofil.com - E-mail: cofil@cofil.com Via G. Rossini 26 - 24040 Casirate D’Adda Bg IT Phone +39 0363

Open the catalog to page 1
Parallel indexing drives 65P.80P.105P.130P - 3

The units of measurement correspond with System International /Severity Index SI General tolerances of manufacture are conform to UNI – ISO 2768-1 UNI EN 22768-1 Illustrations and drawings according to UNI 3970 (ISO 128-82). Method of projection of the drawings. All rights reserved. No part of this catalogue may be duplicated. COLOMBO FILIPPETTI may make any changes they feel necessary for the improvement of their products without advance notice. COLOMBO FILIPPETTI may change any market components and accessories mentioned in this catalogue as they feel necessary. This catalogue supersedes...

Open the catalog to page 3
Parallel indexing drives 65P.80P.105P.130P - 4

SERIES 65P • BOP • 105P • 130PSPECIFICATIONS Index drive code

Open the catalog to page 4
Parallel indexing drives 65P.80P.105P.130P - 5

SERIES 65P • BOP • 105P • 130PSPECIFICATIONS Index drive code Other special motion can be supplied on request

Open the catalog to page 5
Parallel indexing drives 65P.80P.105P.130P - 6

SERIES 65P • BOP • 105P • 130PSPECIFICATIONS Index drive code

Open the catalog to page 6
Parallel indexing drives 65P.80P.105P.130P - 7

DRIVE COMPONENTS - Parallel shaft. - Separate and pre-coupled cam/follower units. - Cam hub with hollow shaft and keyway. - High-strenght alloy steel cam with hardened, ground profiles. - Dial plate with central clearance hole and flange mount on each side. - High load capacity with special yoke-mounted cam followers. Notes • Reversal of the direction of rotation of the input shaft also reverses the direction of rotation of the output shaft, while the kinematic features of the intermittent motion are unchanged. • The keyway of cam hub "T" is located halfway along the pause stretch. • The...

Open the catalog to page 7
Parallel indexing drives 65P.80P.105P.130P - 8

SERIES 65P • BOP • 105P • 130P HOUSED UNITS - Prism-shaped sealed cast iron housing. - Outer surfaces machined, whit support on 6 sides. - Possibility of mounting housing in all positions. - Parallel shafts projecting in input and output. - Roller bearings on opposite taper roller shafts. - Oil-bath lubrication. - Worm gear reducer splined directly to housing. Notes • Reversal of the direction of rotation of the input shaft also reverses the direction of rotatin of the output shaft, while the kinematic features of the intermittent motion are unchanged. • The input shaft keyway is in...

Open the catalog to page 8
Parallel indexing drives 65P.80P.105P.130P - 9

MOUNTING POSITIONS No. of stops index period version — side with input shaft_ side with output shaft_ side with mounting holes side with oil plugs lower side after mounting IDENTIFICATION NUMBER The identification number of the INDEX DRIVE is made up in accordance with the chart. The mounting position of the worm gear reducer in versions VRS, VSP and VSM is specified in the paragraph "REDUCER MOUNTING POSSIBILITIES".

Open the catalog to page 9
Parallel indexing drives 65P.80P.105P.130P - 10

REDUCER MOUNTING POSSIBILITIES The CF3 INDEX DRIVES in versions VSR VSP and VSM are fitted with worm gear speed reducers suitably selected and splined directly to the input shaft. This system presents a combination of rigid power transmission and a very compact motor driven INDEX DRIVE unit. The range of reduction ratios avaitable produces speeds between 14 and 200 indexes/min., thereby meeting the majority of application requirements. The CF3 INDEX DRIVE designed for the worm gear reducer to be splined on, is the VSL long-shaft version. The reducer can be mounted on the CF3 INDEX DRIVE...

Open the catalog to page 10
Parallel indexing drives 65P.80P.105P.130P - 12

Ito create] in movement with the times Products Cam Mechanisms and special products Compact double spherical cam mechanism for mechanical automation Combination of flat cam and globoidal profiled cam Globoidal cam mechanism with four synchronized intermittent movements. Bilateral outputs. Mechanism with different cams producing seven synchronized intermittent and oscillating the culture of precision Flat cam with conjugate profiles

Open the catalog to page 12

All COLOMBO FILIPPETTI catalogs and technical brochures

  1. SRP

    28 Pages

  2. RIGIDIAL EN

    40 Pages

  3. CF3

    16 Pages

  4. H..S

    28 Pages

  5. RIGP

    24 Pages

Archived catalogs