WEDGE BELTS VECO 100® DYNAM® SYSTEM ST - ISO 4184 - DIN 2215 - BS 3790 10005 -1 / 2 Fiche Technique - Technical Data Sheet Function Flexible link between the motor and the machine which allows to transmit installed power in very good conditions. The VECO 100 belts, which are also called "classical belts", are often used on working machines. For a new transmission, think of VECO 200 belts' advantages and performances (see technical data sheet n°10001). Conception Endless V belts are made of: • synthetic rubbers which guarantee a constant hardness • polyester cord with controlled elasticity and high capacity of traction • single wrapping (for Z, A and B sections) and double wrapping (for C and D sections) impregnated with polychloroprene compound which resists heat, oil, abrasion and ozone. General Specifications • Working temperature: -35° to +100°C • antistatic following standard NF T 47 104 / ISO1813 • V belt sections following standard E 24 - 213 • Resistant to oil projection, hydrocarbure and diluted acids. ISO1817 • endure centrifugal strength Stocking conditions See Technical data sheet n°10001-2 Stabilisation Process "ST" The stabilisation process "ST" guarantees a small and continuous margin on the length. The length of V. belts follows the standard NF ISO 4184. It means: - easy to install - even distribution of loads on multiple belt drives - eliminate vibrations On our DYNAM belts, you can read : - the production date (codes month and year) : 6C - ST mark - the pitch length measured under strength, as well as the section : 1545 A60 THE " DYNAM LABEL tension by a simple reading of a length need to check it a second time. (see data Design The DYNAM® system allows us to supply a pre-tensionned belt. This system ensures the correct between 2 points. This measure only needs to be done once when you install your belt. There is no sheet n°10003) Performance - The 1 % slip guarantees a performance of 95 % - Better transmitted power : this system improves the efficiency of V. belt by 20 % - Optimum performance is obtained when the linear speed is between 30 m/s and 33 m/s member of SANOK RUBB

COLMANT CUVELIERrps member of SANOK RUBBER GROUP 02-2018 Pitch lengths of our V.belts (in mm) The sections of V.belts VECO 100® with "label DYNAM" that we can supply are : Z, A, B, C,D. Only the sizes in yellow are available with the DYNAM System. Lp : pitch length ; li : internal length ; le : external length QC0LMANT-CUVELIER-RPS.COM 0 +33(3)20 67 79 01 El CONTACTraCCRPS.COM CUV^UER member of SANOK RUBB

COLMANT CUVEUERrps member ofSANOK RUBBER GROUP 02-2018 WEDGE BELTS VECO 100 DYNAM SYSTEM Determining the transmission - ST - ISO 4184 - DIN 7753 - Fiche Technique - Technical Data Sheet BS 3790- DIN 7753 - BS 3790 10006 - 1 /4 Estimating corrected power : Use the above correction coefficients on the basis of the operating rating, the type of machine to be driven and the nature of the drive force. The corrected power is : Pc = Power x Power correction. Calculation example : driver pulley = 0250 - driven pulley = 250 x 2 = 0500 - for a ratio greater than 3 : 1,2 D Calculating the transmission ratio...

WEDGE BELTS VECO 100 DYNAM SYSTEM Determining the transmission - ST - ISO 4184 - DIN 7753 - BS 3790- DIN 7753 - BS 10006 - 2 / 4 3790 iche Technique - Technical Data Sheet Determining drive belt length (L) The following formula must be used : D + d (D-d)2 Lo = 2E + 3,14 -+ - Calculation example: Lo = 2 x 1100 + 3,14 x (500 + 250)/2 + (500 - 250)2 /(4 x 1100) = 3392 mm Selected length L = 3397 mm Select the standard length L which is the closest to the calculated length Lo. The new distance between axes thus become : E= 1100- (3397- 3392)/2 = 1103 mm 2 2 Determining the actual power belt drive...

WEDGE BELTS VECO 100 DYNAM SYSTEM Determining the transmission - ST - ISO 4184 - DIN 7753 - BS 3790- DIN 7753 - BS 3790 10006 - 3/4 Fiche Technique - Technical Data Sheet 02-2018 Power rating for a V-belt (A section) : Power rating for a V-belt (B section) : 0 small Power rating for a V-belt (C section) : 0 small member of SANOK RUBB

WEDGE BELTS VECO 100 DYNAM SYSTEM Determining the transmission - ST - ISO 4184 - DIN 7753 - BS 3790- DIN 7753 - BS 3790 10006 - 4/4 Fiche Technique - Technical Data Sheet 02-2018 Power rating for a V-belt (D section) : 0 small Speed 30 to 33 : dynamic balancing necessary Beyond 33 m/s : accurate dynamic balancing necessary Keep if possible in the non coloured area

COLMANT CUVELIERrps member of SANOK RUBBER GROUP 02-2018 CLASSICAL V-BELTS VECO 100® AND WEDGE V-BELTS VECO 200® LABEL DYNAM - INSTALLATION GUIDE 10003 1/7 Fiche Technique - Technical Data Sheet A proper installation is an important aspect for transmitting power with a transmission with Veco V-belts. It must respect the parallelism of the shafts, the alignment of the pulleys and the correct setting of the DYNAM® tension device. The installation must also respect the following instructions : • Use identical grooves profiles according to usual norms and tolerances. Make sure that grooves are clean...

CLASSICAL V-BELTS VECO 100â AND WEDGE V-BELTS VECO 200â LABEL DYNAM – INSTALLATION GUIDE With V-belts, the rollers can be used to set the tension when none of the shafts can be moved, or to limit the vibrations. A tensile roller can be flat or with grooves, set on the driven belts (preferably) or on the driving belts, inside (preferably) or outside of the belts. This leads to 6 current positions, shown of the drafts below. The roller’s diameter must be the biggest possible, at least the diameter of the small pulley. Roller on driven belts : Rollers on driving belts : When roller can be blocked,...

COLMANT CUVELIERrps member of SANOK RUBBER GROUP 09-2018 COURROIES VECO 100® ET VECO 200® TROUBLESHOOTING 10004 - 1 / 1 Fiche Technique-TROUBLES AND SOLUTIONS Troubles member of SANOK RUBB