Cleveland-Kidder ®Ultra
6Pages

LOW PROFILE LOAD CELL Cleveland-Kidder ®Ultra SLIM CELL Low Profile Load Cell Providing up to a 40:1 Tension Range • Provides up to a 40:1 Tension Range (Ex: Accurately measures from 1.25 lbs. to 50 lbs. of tension when used with a 50 lb. rated Ultra Load Cell and Ultra Amplifier). • Performance Benefits Cleveland Motion Controls new Ultra Line Slim Cell Transducer is part of the new Cleveland-Kidder® Ultra Line Tension Transducer family. With a unique low-profile design, it sets the standard for either new machinery or for retrofits where space is tight. With a dust sealed, corrosion resisting, water resisting design, it is ideal for use in demanding industrial environments. The Ultra Line Slim Cell Transducer can be used with either rotating shafts or dead shaft rollers and has a flat cylindrical shape. It is designed to reduce the required side-frame-to-sideframe width of the machine. Ultra Line Slim Cells, when used in conjunction with Ultra Line Amplifiers, provide better performance than competitive load cells by increasing the operating tension range from 8:1 to 40:1. They also provide more accurate measurement by eliminating electrical disturbances caused by AC drives, servos, and other modern high frequency devices. Benefits: Advantages Over Conventional Transducers Technical Specifics: How CMC Does It Operates over a wider tension range. Provides up to 40:1 tension range. Competitive products typically provide tension ranges of only 8:1 or 16:1, at the very best. Provides a higher output signal which results in better signal resolution. Full Wheatstone Bridge semiconductor strain gage transducer design provides a higher and more stable signal. “Twin beam” design provides high mechanical gain with negligible displacement. Ability to measure lower (light) tensions. Substantial and stable output signal even at low tensions. New amplifier technology eliminates drift, which distorts low-tension measurements. Does not react to electrical noise from AC motors, servo, relay coils, or other electrical disturbances. Rejects electrical noise resulting in clean and accurate output signal devoid of distortion. Four-wire differential ended technology provides common mode rejection of electrical disturbances. Better at maintaining proper tension measurement regardless of ambient temperature changes. Minimum deviation of signal output due to temperature changes. Precise temperature compensation network cancels out temperature influences. Rejects electrical noise from AC motors, servos, relay coils, or other electrical disturbances. • Available in 10 lb. to 1000 lb. load ratings. • Designed to operate over wide tension ranges. • For use with either rotating shafts or dead shaft rollers. • Low profile design reduces width requirements of machine frame. • Low friction bearing ideal for low tension applications. • Maintenance–free bearing with lifetime lubrication. • Competitively priced alternative to UPB style load cells. • Easily oriented to any web path by rotating transducer (if the wrap angle changes) –no remounting necessary. • Designed to comply with NEMA 4x, IP65 standards. • Completely sealed––corrosion resisting, chemical resisting (Stainless Steel 410) water resisting, and dust sealed. • 500-1000% Overload Ratings.

LOW PROFILE LOAD CELL SLIM CELL Cleveland-Kidder ®Ultra Corrosion Resisting Material: Made from 410 Stainless Steel Mounting Holes: The Slim Cell can be rotated 60 degrees either direction by loosening the mounting bolts to insure proper orientation Labyrinth Seal: •Accommodates angular displacement •Very low friction •Maintenance-free Wave Washer: Accommodates shaft expansion Bearing with lubricant: •Very low friction •Maintenance-free Shaft Adapter with Set Screws: •Insures that shaft is precisely locked in position •Accommodates various shaft diameters Versatile Back Plate: •Can be...

LOW PROFILE LOAD CELL SLIM CELL Cleveland-Kidder ®Ultra PART NUMBER CONFIGURATOR 25 Low Profile Load Cell Providing up to a 40:1 Tension Range LOAD CELL RATING ROLLER SHAFT DIAMETER LOAD CELL BODY SIZE LOAD CELL BACK PLATE ROLLER SHAFT TYPE (See Table 3 Installation Choices) Blank/Flush BF Blank/Pilot BP Hole/Flush HF Hole/Pilot HP ORDERING PROCEDURE: Slim Cell part numbers are configured according to your requirements: 1. Calculate the Maximum Working Force (MWF) rating from the Sizing Calculation equation. From the Part Number Configurator, select a Load Cell Rating that equals or exceeds...

SIZING CALCULATION T= Max Tension A= Wrap Angle (Degrees) W= Roll Weight B= Angle of Tension Force (Degrees) K= Overload for Transients (Nominal 1.5 for most applications) MWF = Maximum Working Force (Used to select the proper force rating of the transducer) Low Profile Load Cell Providing up to a 40:1 Tension Range INDUSTRIAL PRODUCTS 7550 Hub Parkway Cleveland, Oh 44125-5794 Tel: 216-524-8800 or (800) 321-8072 Fax: 216-642-2100 www.CMCcontrols.com Load Cell Rating (lbs.) Table 2: Slim Cell Body Size (Roller Shaft Diameter vs. Load Cell Rating) * The MWF calculation defines the force on...

LOW PROFILE LOAD CELL SLIM CELL Cleveland-Kidder ®Ultra DIMENSION TABLES Slim Cell (alone) Mounting Bracket (with Slim Cell) * For dimensions in inches, allow 2.5 inch clearance for cable connector. ** See Table 2 for permissible Shaft Diameter. Bore Diameter is typically between Nominal Diameter +0.0007 and +0.0017 inch. *** Bolts supplied with bracket Dimensions In Millimeters* SIZE A UltraSLM1 114.3 UltraSLM2 174.3 SIZE UltraSLM1 UltraSLM2 * For dimensions in millimeters, allow 64 mm clearance for cable connector. ** See Table 2 for permissible Shaft Diameter. Bore Diameter is typically...

LOW PROFILE LOAD CELL Cleveland-Kidder ®Ultra SLIM CELL Inside Frame With Dead Shaft With Alignment Pilot BP Blank Back Plate TABLE 3: Installation Choices Outside Frame With Mounting Bracket With Dead Shaft With Dead Shaft With Live Shaft 62 degrees of angular alignment with bolt in position With Dead Shaft Back Plate With Hole With Alignment Pilot BP With Live Shaft With Live Shaft With Dead Shaft With Dead Shaft With Alignment Pilot HP With Alignment Pilot HP Flush With Live Shaft With Live Shaft With Live Shaft PERFORMANCE SPECIFICATIONS GENERAL SPECIFICATIONS Description: Transducer...