Tie rod cylinder SCG
87Pages

{{requestButtons}}

Catalog excerpts

Tie rod cylinder SCG - 1

guided cylinder Conventional switch Compact switch New easy-to-use SCG Series ( 32 to 100) air cylinders - Remove toxic substances and protect the environment by preventing contamination Port and needle on same plane Air supply/exhaust port and cushion needle installation on same side. Cylinder installation/ adjustment, etc. are easier. A T switch smaller than the conventional switch is used. This eliminates switch protrusion in installation, saving space. Switches are installed easily and smoothly with our original switch bracket. Fix with screws alone Installation is completed by tightening screws after adjusting switches. The mechanism sandwiches the tie rod, making the switch position adjustable without supporting the switch. Powerful fixing The T switch in the rail is finely adjustable. Easy switch install Standard magnets Ecological product Harmful substances such as lead and hexavalent chrome that adversely affect the global environment are not used in the cylinder and cylinder switch. This product complies with the RoHS Directives in effect in the EU. (Lead-free solder and lead wires) Switches can be installed on all products. Less installation space is required because the cylinder is up to 40 mm shorter than the conventional cylinder. Products match a variety of equipment with a uniform white exterior. SCG Series Products Model variation Bore size Standard type Position locking type Same dimensions for rubber scraper type (G), coolant proof type (G1, G2) and spatter adherence prevention type (G4) The dimensions of the rubber scraper and spatter adherence prevention are the same as the standard type, facilitating installation. Low friction type Double rod type Non-rotating type Tie rod cylinder Standard type Rubber scraper type Coolant proof type Spatter adherence type

Open the catalog to page 1
Tie rod cylinder SCG - 2

Series variation SCG Series Series variation Double acting low speed type Double acting low friction type Double acting double rod type Double acting non-rotating type Double acting powerful scraper type Double acting coolant proof type SCG-G4 Double acting spatter adhesion prevention type Trunnion type No. 2 bracket Clevis bracket Piston rod material stainless steel Copper and PTFE free Consult with CKD. Consult with CKD. Double acting position locking type Double acting single rod type Tie rod cylinder Standard type Both sides rubber cushion Both sides air cushion :Custom order, Center...

Open the catalog to page 2
Tie rod cylinder SCG - 3

Variation and option selection table : Standard : Option : Available (custom order) : Available depending on conditions X : Not available Port thread Double acting single rod type Non-rotating type Position locking type Low speed type Low friction type Rubber scraper type Coolant proof scraper (NBR) Coolant proof scraper (FKM) Spatter adherence prevention type Port thread With bellows (polyolefin material) Piston rod material stainless steel Copper and PTFE free type Customized piston rod end form Cylinder switch Rod eye Rod clevis Eye bracket Clevis bracket Eye bracket Trunnion type No. 2...

Open the catalog to page 3
Tie rod cylinder SCG - 4

Pneumatic components Safety precautions Always read this section before starting use. Refer to Intro 71 for general notes of cylinders and Intro 78 for cylinder switches. Design & Selection 2. Position locking type SCG-Q Install a flow control valve on the cylinder. Install a flow control valve on the cylinder. Use within the applicable piston speed range for each cylinder. Either a rubber or air cushion type cushion mechanism is assembled in the cylinder. The air cushion absorbs kinetic energy the piston acquires using air compression, and prevents the piston and cover from colliding at...

Open the catalog to page 4
Tie rod cylinder SCG - 5

SCG Series 4. Coolant proof type SCG-G2/G3 3. Low friction type SCG-U Durability differs based on working conditions and model features. This cylinder is the cylinder which has internal leakage. Refer to the specification on page 392 for the internal leakage volume. Do not apply the deviated load onto the piston rod. It could shorten scraper and bearing life. If coolant or water do not get on the G2 or G3 series, the piston rod lubrication could be spent and shorten life. Use the G Series in this case. When a balancer, etc., is used, a flow control valve should not be installed if supply...

Open the catalog to page 5
Tie rod cylinder SCG - 6

SCG Series Installation & Adjustment Supply a pressure higher than the minimum working pressure to the port having the locking mechanism. Precautions for switch installation Assembling the switch bracket When assembling the cylinder onto the switch bracket, fit the tie rod to be installed into the bracket, and move the switch so that it is at the center of the operation range (ON range). Then, tighten the fixing bolts with a tightening torque of 0.6 to 0.9 N·m. The bracket position (GC, DD) and switch positions (RD, HD) at which the maximum sensitivity is attained at both stroke ends are...

Open the catalog to page 6
Tie rod cylinder SCG - 7

SCG Series During Use & Maintenance 1. Position locking type SCG-Q Releasing the nonlocking manual override The stopper pin moves and the lock is released when the release SCM bolt is screwed into the stopper piston and the bolt is pulled up tion or when counter side port is pressurized). When the hand is released, if the stopper piston returns by the internal spring and CA/OV2 enters the piston rod groove, the piston is locked. SSD Release bolt Stopper spring Stopper piston When using the cylinder with air cushion, if the air cushion needle on the lock mechanism side is tightened too...

Open the catalog to page 7
Tie rod cylinder SCG - 8

CMK2 CMA2 SCM SCG SCA2 SCS CKV2 CA/OV2 SSD CAT MDC2 MVC SMD2 MSD* FC* STK ULK* JSK/M2 JSG JSC3 USSD USC JSB3 LMB STG STS/L LCS LCG LCM LCT LCY STR2 UCA2 HCM HCA SRL2 SRG SRM SRT MRL2 MRG2 SM-25 CAC3 UCAC RCC2 MFC SHC GLC Ending

Open the catalog to page 8
Tie rod cylinder SCG - 9

Tie rod cylinder, double acting single rod type Bore size: Bore size Double acting Working fluid Withstanding pressure Ambient temperature Port size Rubber cushioned Working piston speed Effective air cushion length mm 30 to 1000 (use within the allowable energy absorption. ) Selection of air cushion and rubber cushion possible 13.4 Not required (when lubricating, use turbine oil Class 1 ISO VG32.) Allowable energy Rubber cushioned Stroke length Bore size (mm) Standard stroke length (mm) Max. stroke length (mm) Available stroke length (mm) Min. stroke length (mm) 700 32 Note 1: The custom...

Open the catalog to page 9

All CKD catalogs and technical brochures

  1. MN4GA / 4GB

    140 Pages

  2. MV3QR

    16 Pages

  3. SCP*3 Series

    60 Pages

  4. SCS2 series

    56 Pages

  5. LMD series

    15 Pages

  6. KBZ series

    64 Pages

  7. WXU series

    32 Pages

  8. AX6000M

    24 Pages

  9. SCS-G Series

    2 Pages

  10. CMK2 SR

    7 Pages

  11. SCPD2 Serie

    3 Pages

  12. SCPD2 Series

    2 Pages

  13. SCPS Series

    1 Pages

  14. SCM Series

    2 Pages

  15. GHV series

    4 Pages

Archived catalogs