Eliminate bothersome design and assembly Guided compact cylinder GUIDED COMPACT CYLINDER SSG SERIES

Eliminate bothersome design and assembly by directly installing on a load! The SSG Series providing the super compact cylinder SSD series with a guide Versatile plat series to improve lateral load res»s:ance end revoJvaHe angle iterance Compatible installation The super compact cylinder has a versatile plate that eliminates bothersome design ar>d assemWy hstalaicn spacing is conp wth the super compeer cy tnder SSO series, enafelng cylinders lo be charged siroothr/ Bore i ■ SSG series products table Series variation Bore size Cylinder switch grooves on four faces The cylinder smtch can be installed...

Safety precautions Always read this section before starting use. When designing and manufacturing a device using CKD products, the manufacturer is obligated to check that device safety mechanism, pneumatic control circuit, or water control circuit and the system operated by electrical control that controls the devices is secured. It is important to select, use, handle, and maintain the product appropriately to ensure that the CKD product is used safely. Observe warnings and precautions to ensure device safety. Check that device safety is ensured, and manufacture a safe device. WARNING 1 This...

Pneumatic components Safety precautions Always read this section before starting use. Refer to Pneumatic Cylinders (CB-029SA) for details on general cylinders and cylinder switches. Design & Selection CAUTION Use within the allowable load. Use exceeding the allowable lateral load and rotation torque may result in damage, etc. Refer to the selection guide on page 10. Do not use as a stopper. Use this product in application such as pushers and lifters that are not subject to shocking lateral loads. When using this with the cylinder pushed in the middle of the stroke, check that thrust is applied...

Safety precautions Installation & Adjustment CAUTION Check that no dents or damages occur on the end plate that could compromise atness. Flatness of the counterpart on which the end plate is installed must be 0.05 mm or less. Allowable energy absorption Use within the allowable energy absorption range. Provide the other cushioning outside if exceeding allowable energy absorption range. Refer to the Specifications for allowable energy absorption values. During Use & Maintenance CAUTION Do not disassemble this product. The performance may be compromised.

Guided compact cylinder double acting single rod type Specications Descriptions Bore size mm Actuation Working uid Max. working pressure MPa Min. working pressure MPa Withstanding pressure MPa Ambient temperature °C Port size No cushion Stroke tolerance mm Rubber cushioned Working piston speed mm/s Cushion Lubrication No cushion Allowable absorbing energy J Rubber cushioned ø32 ø40 Double acting Compressed air 1.0 50 to 500 50 to 300 Selection of no cushion or rubber cushion is possible Not required (when lubricating, use turbine oil Class 1 ISO VG32.) 0.016 0.021 0.025 0.092 0.1 0.12 0.27 0.10...

Switch specications (T type switch) 1 color/2 color indicator/strong magnetic eld proof Descriptions Applications Output type Power voltage Load voltage Load current Light Leakage current relay and small solenoid valve controller dedicated 85 to 265 VAC 10 to 30 VDC 24 VDC 10% 5 to 100mA 5 to 20mA (Note 1) Red/green Red/green LED LED LED LED (ON lighting) (ON lighting) (ON lighting) (ON lighting) 1mA or less with 100 VAC 1mA or less 2mA or less with 200 VAC For programmable For programmable controller, relay, IC controller and relay NPN output PNP output NPN output NPN output 10 to 28 VDC 30...

With switch Model no. Bore size Stroke length The intermediate stroke can be manufactured in 1 mm increments. (Less than 5 mm with switch is not available.) Total length of the intermediate stroke is the same as the next larger standard stroke. Note on model No. selection Note 1: T0* or T5* switches can not be installed for 5 mm stroke length of ø12, ø16. Note 2: T2YD* switch can not be installed for ø12, ø16. Note 3: T8* switch can not be installed for ø12 to ø32. Note 4: F type switch is installable only on the piping port of tube bore size ø25. Switch model No. Note 1 Note 2 Note 3 Note 4...

Internal structure and parts list Internal structure and parts list (ø12 to ø50) (no cushion) SSG-L-12 to 15 (double acting, with switch) SSG-L-32 to 50 (double acting, with switch) Section C (When stroke length 50 is exceeded.) Section C (When stroke length 50 is exceeded.) Hexagon socket head bolt (ø12) Alloy steel Zinc chromate Plastic Nitrile rubber Hexagonal socket button bolt (ø16 to 50) Alloy steel Zinc chromate Piston packing seal Aluminum alloy C type snap ring Special aluminum alloy Alumite Aluminum alloy Nitrile rubber Hexagon socket head bolt Alloy steel Nitrile rubber Aluminum alloy...

SSG Series Internal structure and parts list (ø63 to ø100) (no cushion) SSG-L-63 to 100 (double acting, switch) Section C (When stroke length 50 is exceeded.) Section C (When stroke length 50 is exceeded.) Hexagon socket head button bolt Alloy steel Zinc chromate Aluminum alloy Aluminum alloy Piston packing seal Nitrile rubber Nitrile rubber Aluminum alloy C type snap ring Aluminum alloy Nitrile rubber Hexagon socket head bolt Alloy steel Aluminum alloy Bush Body Aluminum alloy Chromate Alumite Zinc chromate Oil impregnated bearing alloy Hard alumite Aluminum alloy Industrial chrome plating Aluminum...

Internal structure and parts list Internal structure and parts list (ø12 to ø32) (rubber cushioned) SSG-L-12D (double acting, with switch) SSG-L-16D to 32D (double acting, with switch) Section C (Only when 32 stroke length 50 is exceeded) Hexagon socket head bolt (ø12) Hexagon socket head button bolt (ø16 to ø32) Alloy steel Zinc chromate Aluminum alloy C type snap ring Nitrile rubber Section C (Only when 32 stroke length 50 is exceeded) Piston packing seal Nitrile rubber Aluminum alloy Plastic Chromate Nitrile rubber Cushion rubber Special aluminum alloy Alumite Hexagon socket head bolt Alloy...