CENTADISC-C
17Pages

{{requestButtons}}

Catalog excerpts

CENTADISC-C - 1

CENTA PRODUKT R A NSMISSIO N C E NTA P OWER T DOKUMENTATION CENTADISC-C ENGL ISH Is this PDF up to date? click here for an update check!

Open the catalog to page 1
CENTADISC-C - 2

CENTA PRODUCT DOCUMENTATION TECHNICAL DATA Product selection: Product application: technical data which purpose? which coupling Is this PDF up to date? click here for an update check! CD-C-EN-09-16 | PAGE 2 | PUBLISHED 23. September 2016 | MAIN MENU

Open the catalog to page 2
CENTADISC-C - 3

CENTA PRODUCT DOCUMENTATION CENTADISC-C – a torsionally stiff light weight membrane coupling for the application in vessels, ferries and in wind energy applications where weight and alignment are of high importance. Two membranes arranged in series and combined with a fibre reinforced tube function as kinematic joint with optimum operating characteristics. The combi-nation with further CENTA products, cardanshafts, homokinetic joints or couplings on the other shaft end guarantees optimal adaption. Stiff and lightweight tubes allow high bending speeds thus longer driveshafts are possible...

Open the catalog to page 3
CENTADISC-C - 4

Lightweight solutions often are The combination with further The maintenance effort is very low When the going gets tough, quality subject to comprise in regard of series compensate for significant CENTA products, cardanshafts, and upon intended use there is no is priceless. With an exemplary torsional stiffness. The use of light misalignments in axial, radial and homokinetic joints or couplings on Quality Management, CENTA en- materials on CENTADISC-C though angular directions. the other shaft end guarantee for sures products that withstand the optimal adaption and appropriate make it...

Open the catalog to page 4
CENTADISC-C - 5

CENTA PRODUCT DOCUMENTATION CENTADISC-C CENTAFLEX-A APPLICATIONS APPLICATIONS Which product for your purpose? We will gladly assist → www.centa.info/contact CD-C-EN-09-16 | PAGE 5 | PUBLISHED 23. September 2016 | MAIN MENU

Open the catalog to page 5
CENTADISC-C - 6

CENTA PRODUCT DOCUMENTATION CENTADISC-C APPLICATIONS MARINE APPLICATIONS WIND APPLICATION GENER ATOR Which product for your purpose? We will gladly assist → www.centa.info/contact CD-C-EN-09-16 | PAGE 6 | PUBLISHED 23. September 2016 | MAIN MENU

Open the catalog to page 6
CENTADISC-C - 7

CENTA PRODUCT DOCUMENTATION TECHNICAL DATA TECHNICAL DATA DIMENSIONS CD-C-EN-09-16 | PAGE 7 | PUBLISHED 23. SEPTEMBER 2016 | MAIN MENU ^ CHECK FOR UPDATES

Open the catalog to page 7
CENTADISC-C - 8

CENTA PRODUCT DOCUMENTATION CENTADISC-C TYPE 0 TECHNICAL DATA J, SIZE 0-5 CD-C-EN-09-16 | PAGE 8 | PUBLISHED 23. SEPTEMBER 2016 | MAIN MENU

Open the catalog to page 8
CENTADISC-C - 9

CENTA PRODUCT DOCUMENTATION CENTADISC-C TYPE 0 alternative: short Adapter CD-C-EN-09-16 | PAGE 9 | PUBLISHED 23. SEPTEMBER 2016 | MAIN MENU ^ CHECK FOR UPDATES

Open the catalog to page 9
CENTADISC-C - 10

CENTA PRODUCT DOCUMENTATION CENTADISC-C TYPE G TECHNICAL DATA J, SIZE 0G-4G ** continuous allowable value for DNV classification is 1° CD-C-EN-09-16 | PAGE 10 | PUBLISHED 23. SEPTEMBER 2016 | MAIN MENU

Open the catalog to page 10
CENTADISC-C - 11

CENTA PRODUCT DOCUMENTATION Dimension L* is produced according customers requirements, but is nevertheless dependant upon speed. We are at your service for consultation. The dimensions of the connecting flanges (D5, D6, D7, d6) comply with our company standards. Deviating tailored flanges are possible. Each side of the universal joint shaft can either be equipped with hubs or connecting flanges. The flanges are available with dimension L2 in short version or with dimension L3 in long version. The materials available for hubs and flanges are steel, aluminium or titanium. CD-C-EN-09-16 | PAGE...

Open the catalog to page 11
CENTADISC-C - 12

CENTA PRODUCT DOCUMENTATION CENTADISC-C EXPL ANATION OF THE TECHNICAL DATA This appendix shows all explanations of the technical data for all CENTA products. the green marked explanations are relevant for this catalog: 1 Size 5 Continuous vibratory torque 6 Permissible power loss 7 Dynamic torsional stiffness 10 Permissible axial displacement 12 Permissible radial displacement 14 Permissible angular displacement Are these technical explanations up to date? click here for an update check! CD-C-EN-09-16 | PAGE APP-1 | PUBLISHED 23. September 2016 | MAIN MENU

Open the catalog to page 12
CENTADISC-C - 13

CENTA PRODUCT DOCUMENTATION This spontaneously selected figure des- This figure indicates the nominal shore ignates the size of the coupling. hardness of the elastic element. The nominal value and the effective value may deviate within given tolerance ranges. Nominal torque Tkn [kNm] Average torque which can be transmitted continuously over the entire speed range. This is the torque that may occur occasionally and for a short period up to 1.000 times and may not lead to a substantial temperature rise in the rubber element. In addition the following maximum torques may occur: Continuous...

Open the catalog to page 13
CENTADISC-C - 14

CENTA PRODUCT DOCUMENTATION The maximum speed of the coupling element, which may occur occasionally and for a short period (e.g. overspeed). The dynamic torsional stiffness is the relation of the torque to the torsional angle under dynamic loading. The torsional stiffness may be linear or progressive depending on the coupling design and material. The value given for couplings with linear torsional stiffness considers following terms: • Pre-load: 50% of Tkn • Amplitude of vibratory torque: 25% of Tkn For couplings with progressive torsional stiffness only the pre-load value...

Open the catalog to page 14
CENTADISC-C - 15

CENTA PRODUCT DOCUMENTATION CENTADISC-C EXPLANATION OF THE TECHNICAL DATA 11 The axial stiffness determines the axial reaction force on the input and output sides upon axial displacement. By experience the dynamic stiffness is higher than the static one. The factor depends on the coupling series. The continuous permissible radial displacement of the coupling. This is the sum of displacement by assembly as well as static and dynamic displacements dur-AK- ing operation. The continuous permissible radial displacement depends on the operation speed and may require adjustment (see diagrams Sn...

Open the catalog to page 15
CENTADISC-C - 16

CENTADISC-C © 2016 by CENTA Antriebe Kirschey GmbH Rev. CD-C-EN-09-16 1. This catalog supersedes previous editions. This catalog shows the extent of our CENTAX®-SEC coupling range at the time of printing. This program is still being extended with further sizes and series. Any changes due to technological progress are reserved. We reserve the right to amend any dimensions or detail specified or illustrated in this publication without notice and without incurring any obligation to provide such modification to such couplings previously delivered. Please ask for an application drawing and...

Open the catalog to page 16

All CENTA POWER TRANSMISSION catalogs and technical brochures

  1. CENTAFLEX-B

    8 Pages

  2. CENTAFLEX-A

    36 Pages

  3. CENTADISC-T

    1 Pages

  4. CENTADISC-M

    8 Pages

  5. CF-RS

    6 Pages

  6. CF-RV

    8 Pages

  7. CF-T

    14 Pages

  8. CF-X

    8 Pages

  9. CJ

    2 Pages

  10. CL

    16 Pages

  11. CM-B

    8 Pages

  12. CM-G

    4 Pages

  13. CM-HTC

    4 Pages

  14. CM-S

    24 Pages

  15. CS-V

    12 Pages

  16. CX-K

    18 Pages

  17. CX-SEC

    108 Pages

  18. CX-Test

    9 Pages

  19. CX-TT

    14 Pages

  20. CX-V

    20 Pages

  21. CENTA-SCS

    15 Pages

  22. CENTAMAX - B

    8 Pages