CC-75-500
5Pages

CC-75-500 Converter for driving permanent-magnet synchronous motors (PMSM) and brushless DC motors (BLDC). ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ Sensorless speed control from 0 rpm to 1 Million rpm Maximum output power of 500 W (800 W resp.) No output filter required User definable setup for different motor parameters Customer-definable input and output connections Torque or speed control Internal or external braking chopper Highest possible efficiency Mountable on a DIN-rail Parallel connection of several converters to one DC-Bus possible User-friendly PC control software (CelerotonPilot) Specifications converter Input voltage Uin (DC) Maximum output power Output voltage (peak value phase-phase) Maximum phase current (PAM-operation) Maximum frequency/speed (PAM-operation) Operating range Communication interface Optional communication interfaces Communication interface upon request PC control software Weight Dimensions Operating temperature Fundamental of the PAM block current All rights reserved. All information in this document is based on Celeroton’s best knowledge and is not to be considered as a warranty or quality specification. The information given is designed as a guidance and customers are requested to check the suitability and usability of the product in their specific application with consulting Celeroton. The information herein is subject to change without notification.

User interface (X2, X3, X4) Standard configuration E01 Connector X2 – Motor Interface (8 pins) 1 x GND 3 x Digital hall sensor inputs 1 x Power supply 1 x Temperature measurement input 1 x Temperature measurement input 1 x Analog GND (open collector), pull up to 5 V 5 V, 100 mA PTC or NTC, resistance range according to option Tx Thermocouple type K Connector X3 – Digital Interface (8 pins) 1 x GND 1 x Digital GND Digital GND for digital inputs 0 – 24 V, galvanically isolated (software adjustable thresholds 0.8 – 20 V) Common rail for digital outputs 0 – 24 V (Relay, normally open contacts)...

Operating range The operating range of the converter is dependent on the output voltage (Uout) (peak value phase-phase) in Figure 1. The output power (Pout) increases with the output voltage as the phase current (iph) is constant until the power limit is reached. Above that point iph decreases with increasing output voltage. The input voltage (Uin) (grey area) must be higher than the maximum required output voltage. The maximum output power (Pout) of the converter CC-75-500 depends on the ambient temperature (Tamb). The average power losses in the breaking chopper (Pchopper) are limited by...

Order codes: CC-75-500.HC.Exx.SLx.CO1.Tx High current HC HC Version with 800 W output power Extension Board Exx (Configuration of the connectors X2, X3, X4) E01 (standard) Standard – see page 2 Standard configuration E01 Sensorless SLx SL1 (standard) Speed constants between 550 and 18,250 rpm/V Sensorless speed control from 7,000 rpm Speed constants between 400 and 7,900 rpm/V Sensorless speed control from 5,000 rpm The stated values are valid for number of pole pairs p=1. For higher number of pole pairs the speed constants and minimum speeds are divided by the number of pole pairs p....

Celeroton AG | Industriestrasse 22 | 8604 Volketswil | Switzerland T: +41 44 250 52 20 | F: +41 44 250 52 29 | info@celeroton.com All rights reserved. All information in this document is based on Celeroton’s best knowledge and is not to be considered as a warranty or quality specification. The information given is designed as a guidance and customers are requested to check the suitability and usability of the product in their specific application with consulting Celeroton. The information herein is subject to change without notification.