PA Axial Piston Pumps
13Pages

Axial Piston Pump PA Pumps have the following advantages ; • Simple to use, • Economical Conception, • High Rotating Speeds, • High Output Pressure, • 350 bar Cont. Work. Pressure, • 400 bar Peak Pressure, • From 40cc to 90cc, • Low Noise Level, • High Efciency • Special Cast Iron with Raw Materials.

Ordering Code of PA Pumps Pump Code Suction Fittings A Suction Fittings O Without Fittings N PA Axial Piston Pump, Fixed Displacement Formulas Pump Output Flow HP = (Q ×P) / 1714 × E Eoverall = HPOut / HPIn X 100 Overall Efciency = Volumetric Eff. × Mechanical Eff. Pump Efciency Overall Efciency = Output HP / Input HP Pump Input Horsepower EOverall = EffVol. × EffMech. Pump Volumetric Efciency Volumetric Efciency = Actual Flow Rate Output (GPM) / Theoretical Flow Rate Output (GPM) × 100 EffVol. = QAct. / QTheo. X 100 Pump Mechanical Efciency Mechanical Efciency = Theoretical Torque to Drive...

Technical Data Theoretical oil ow l/min at pump speed Maximum Pump Speed Weight - Without inlet tting - With inlet tting Rotation Fluid Mineral Based Hydraulic Oils

Efficiency Curves (lOOOrpm) Quick Calculation Flow rate Torque Power Vg = Geom. dicplacement (ccm/rev.) TIv = Volumetric efficiency Ap = Diff. pressure (bar) rimh = Mechanical-hydraulic efficiency n = Speed (rpm) T|T = Total efficiency (nt = TIV ■ T|MH)

Dimensions Size; Max. Continuous Pump Speed Max. Limited Pump Speed Weight without inlet tting Weight with inlet tting

Dimensions Size; Max. Continuous Pump Speed Max. Limited Pump Speed Weight without inlet tting Weight with inlet tting

Dimensions Size; Max. Continuous Pump Speed Max. Limited Pump Speed Weight without inlet tting Weight with inlet tting

Dimensions Size; Max. Continuous Pump Speed Max. Limited Pump Speed Weight without inlet tting Weight with inlet tting

Inlet Fittings, Accessories I Straight Fittings Hydraulic Adapters

Inlet Fittings, Accessories II Hydraulic Adapters - PTO Piston Pump Adapter - PTO Gear Pump Adapter - Long / Short Adapter Couplars - 6 x 8 Couplar - 6 x 8 Couplar ( Long ) - 8 x 8 Couplar - 8 x 8 Couplar ( Long )

Installation & User Guide The PA pumps tted with a rubber front seal. INSTALLATION PA pumps are direct mounting on the PTO. Grease the splined shaft before installation. Do not tap the gear wheel/driver into position. Remove any mounted screws on the pump. The PA was delivered with protective covers and plastic/threaded plugs. It should be removed before of install.Please check seals and surfaces.If sealing or other surfaces damaged please contact your responsible Service Partner. Start up and run the pump at medium speed (800 to 1000 rpm at the PTO) until the oil owing out of the pump. (...

Complete Product Range Piston Pumps Piston Motors Fixed Plug-in P2 Connection M8x125 Woodruff key 3x6,5 NF E 27-653 NF R 124-04 (2 BOLTS)

ÇELEBİ HİDROCEL OTOM. SAN. TİC. LTD. ŞTİ. Fevziçakmak mh. Aslım Cd. No: 53 C Karatay / KONYA Phone : +90 (332) 345 13 70 +90 (332) 345 13 71 Fax : +90 (332) 345 13 72 hidrocel@hidrocel.com.tr