ETS - Magnetic Drive Metallic Pump
8Pages

{{requestButtons}}

Catalog excerpts

ETS - Magnetic Drive Metallic Pump - 1

Metallic Magnetic Drive Centrifugal Pumps Comply to : 2006/42/CE Design to : Sub-ISO 2858 ATEX 100 Directive 2014/34/EC Flanged UNI 1092-1 (ISO 7005-2 ) PN16RF type B Metallic Magnetic drive Horizontal - Single Stage - Centrifugal pumps Sub-ISO designed Materials : AISI 316 (1.4408) Close-coupled execution

Open the catalog to page 1
ETS - Magnetic Drive Metallic Pump - 2

Mag drive concept The synchronous drive configuration is based on an outer magnet ring assembly couple with an inner magnet ring assembly. With smaller plants come smaller hydraulic requirements, which lend themselves to sub-ISO sized pump units to offer optimum pump efficiency and longer MTBF (Mean time Between Failure). Suitable for handling aggressive, toxic and These two magnet rings are locked together by the flux of attracting magnet poles flowing through the containment isolation shell. hazardous liquids (low viscosity, clean or slightly petrochemical and pharmaceutical industries,...

Open the catalog to page 2
ETS - Magnetic Drive Metallic Pump - 3

3D VIEW Inner and Outer magnets are equipped with NdFeB (neodymium iron boron) or SmCo (samarium cobalt) permanent magnets. Patented cage magnet attachment guarantees stability during the operation of the pump. Sealless design Total containment, essential for hazardous, aggressive or valuable product. Metallic Sealless Magnetic Drive Pumps suitable for service up to 140 °C (optional execution available to reach 180 °C). The ETS series is designed with a rotating metallic shaft supported by single static bushing. Minimal downtime / fast maintenance The clever execution allow the end user to...

Open the catalog to page 3
ETS - Magnetic Drive Metallic Pump - 4

FEATURES IMPELLER Bonus casing thickness made by AISI 316 (CF8M) minimum 3 mm corrosion One piece solid cast stainless steel AISI 316 (CF8M) construction casing life against corrosion and erosion The problem of reverse rotation during start-up has been eliminated thanks to the key driven system complete and fast draining of the casing ISOLATION SHELL • The design allows to the Isolation Shell to be self-venting and fully drainable The rib on the bottom is a perfect vortex breaker which increases the lifetime Isolation shell temperature probe connection provided as a standard INNER MAGNET •...

Open the catalog to page 4
ETS - Magnetic Drive Metallic Pump - 5

PERFORMANCE FIELDS Not binding data refers to water at ream temperature. For specific performance curve contact CDR Pompe S.r.l

Open the catalog to page 5
ETS - Magnetic Drive Metallic Pump - 6

PAINTING COATING QUALITY The metal surfaces are protected by a high performance three coating layers (240 micron) • Epoxy zinc paint • Epoxy amidic modified vinyl • Epoxy enamel paint or aliphatic acrylic polyurethane Available upon request : EN ISO 12944-5 C5M and C5I protecting paint system grades

Open the catalog to page 6
ETS - Magnetic Drive Metallic Pump - 7

LI dimension is according to installed motor manufacturer Flanges dimensions according to UNI 1092-1 ISO \ 7005-1 PN16 type B - slotted ANSI 150 RF

Open the catalog to page 7
ETS - Magnetic Drive Metallic Pump - 8

C.D.R. Pompe S.r.l. Via Raffaello Sanzio, 57 - 20021 Bollate (MI) - Italy Tel. +39029901941 Fax +39029980606 www.cdrpompe.com rdo@cdrpompe.com Technical Characteristics The technical data and characteristics stated in this General Catalogue are not binding. CDR Pompe S.p.a. reserves the right to make modifications without notice. Therefore data, dimensions, performances and any other stated issues are indicative only and not binding. Anyway for any technical details you must require an up-to-date product technical card.

Open the catalog to page 8

All CDR Pompe catalogs and technical brochures