TL642C Telehandler
2Pages

{{requestButtons}}

Catalog excerpts

TL642C Telehandler - 1

Cat ® TL642C Telehandler Specifications Engine Model Gross Power (Basic) Maximum Torque (Standard) Bore Stroke Displacement Boom Performance Cat C3.4B Tier 4 Interim 75 kW 100.6 hp 420 Nm at 1400 rpm 310 lb-ft 99 mm 3.9 in 110 mm 4.3 in 3.4 L 207 .5 cu in ® Weights Operating Weight 9637 kg 21,245 lb Operating Specifications Rated Load Capacity Maximum Lift Height Maximum Forward Reach Frame Leveling Top Travel Speed Capacity at Max Height Capacity at Max Reach Turning Radius over Tires Drawbar Pull (Loaded) Boom Up Boom Down Tele In Tele Out Axles • Trunnion mounted planetary 55 degree steer axles. • Integral steer cylinder. • High bias limited slip differential on front axle. Brakes 2948 kg 12.8 m 9.1 m 10° 33 kph 2948 kg 317 kg 3.7 m 93.4 kN 6,500 lb 42 ft 30 ft 20.5 mph 6,500 lb 700 lb 12 ft 21,000 lb • Service Brakes are inboard wet disc brakes on front and rear axles. • Parking Brakes are spring-applied hydraulic release on front axle. Light on dash indicates when brake is on. Work Tools Hydraulic IT Coupler Pallet Forks Hydraulic System Gear Pump Single-section System Operating Pressure 276 bar 4,000 psi • Auxiliary Hydraulic Circuit used for all attachments equipped with cylinders or other hydraulic components. Consists of valves, controls and hydraulic lines. Service Refill Capacities Fuel Tank Hydraulic System 144 L 132 L 38 gal 35 gal Tires Standard Optional 370/75-28 Duraforce MT 370/75-28 Foam Filled 13.00 x 24 Foam Filled 13.00 x 24 12 PR Transmission Speeds Forward Reverse 13 Seconds 9.7 Seconds 15 Seconds 14.9 Seconds 4 speed 3 speed Lumber Forks Cubing Forks Carriages: Standard Tilt Wide Tilt Side Shift Standard Rotate Wide Rotate Swing Dual Fork Positioning Includes Auxiliary Electrics (2) 1220 mm, 60 mm x 125 mm (2) 1220 mm, 60 mm x 100 mm (2) 1525 mm, 60 mm x 150 mm (2) 1525 mm, 45 mm x 180 mm (2) 1829 mm, 50 mm x 150 mm (2) 1220 mm, 50 mm x 50 mm Includes Auxiliary Electrics (2) 48 in, 2.36 in x 5 in (2) 48 in, 2.36 in x 4 in (2) 60 in, 2.36 in x 6 in (2) 60 in, 1.75 in x 7 in (2) 72 in, 2 in x 6 in (2) 48 in, 2 in x 2 in 1270 mm 1829 mm 1220 mm 1270 mm 1829 mm 100°, 1829 mm, 2948 kg Capacity, 2268 kg Swung 50 in 72 in 48 in 50 in 72 in 100°, 72 in, 6,500 lb Capacity, 5,000 lb Swung 1270 mm 50 in

Open the catalog to page 1
TL642C Telehandler - 2

TL642C Telehandler Dimensions 2.38 m (94 in) All dimensions are approximate. 416 mm (16.4 in) 3.25 m (128 in) 2.41 m (95.5 in) 5.63 m (221.6 in) Load Chart and Dimensions 13.4 m (44 ft) IMPORTANT 70° E D -10 10 40 20 30 TL642C 1.2 m (4 ft) 0° Use only approved attachments with proper material handler model/attachment 10° load capacity charts displayed in the 2.4 m (8 ft) operator’s cab. OSHA requires all rough terrain forklift operators be trained according to OSHA 29 CFR 1910.178 (1). 1.2 m (4 ft) 0° 294 0 m (0 ft) 0 m (0 ft) -1.2 m (-4 ft) 4.9 m (16 ft) the allowable load. 2722 kg (6,000...

Open the catalog to page 2

All Caterpillar Equipment catalogs and technical brochures

  1. Cat® 226D3

    4 Pages

  2. Cat® 8000

    2 Pages

  3. Cat® 279D

    4 Pages

  4. 816F Series 2

    20 Pages

  5. C10302115

    2 Pages

  6. C10302112

    5 Pages

  7. PL87 Pipelayer

    16 Pages

  8. PL61 Pipelayer

    20 Pages

  9. Backhoe Loader

    20 Pages

  10. Telehandler

    2 Pages

  11. Rotary Mixer

    16 Pages

  12. Asphalt Paver

    12 Pages

  13. Forwarder

    4 Pages

  14. Compactors

    20 Pages

  15. Cold Planer

    16 Pages

Archived catalogs

  1. Wheel Dozer

    20 Pages

  2. Motor Grader

    20 Pages

  3. Backhoe Loader

    20 Pages

  4. Pipelayer

    20 Pages