TELESCOPIC HANDLERS

The TX telehandler range is powered by high output Case engines, offering 99 hp on TX13Ü-33 model and now 118 hp from a new climate friendly Tier III low emissions engine in the TX130-40 and above. This engine combines low fuel consumption with a strong 516 Nm of torque, enough to pull the machine through the toughest of site conditions. All engines are mounted longitudinally on the side of the machine, for a maximum transfer of power High output. Low emissions and consumption. REACHING HIGH Robust boom construction with powerful hydraulic cylinders, or chain extension on one 13 m model, offers...

Powershift transmissions handle high power delivery without heat build-up. Smooth gear shifting and three steering modes ensure that the operator can work in the toughest site conditions. Four wheel steering greatly reduces turning circle, while crab steer offers the perfect solution when working against obstacles. Outstanding manoeuvrability. Reliable components. TOTAL CONTROL With standard pilot controls for all hydraulic functions the Case TX telehandler is an easy machine to drive. Load sensing, flow sharing hydraulics, in combination with a smooth Powershift transmission, ensure independent...

The TX range uses robust telescopic booms with inherent rigidity and strength to allow many hours of safe lifting. The TX13Ö-33 has a chain driven extension for the second boom section, while all larger machines use an internally mounted hydraulic twin cylinder to extend the boom. All models are equipped with safety valves on the lift, tilt and stabiliser cylinders, to prevent the boom dropping in the case of hose failure. Visual and audible warning devices signaling overload are incorporated in the upper right corner of all cabs. On TX130-40 and above models, a strict safety device automatically...

From its initial concept From its initial conception the Case telehandler cab lias led the field in terms of ergonomics, visibility and safety. Its curved top with wrap around glazing offers unparalleled visibility of the boom and the load. A glazed door, with opening window, provides easy access to the cab and the deep glass, low engine canopy and low boom pivot point ensure an excellent view all around the machine. This is a major contributing factor to increased site safety and prevents damage to the machine when manoeuvring in confined spaces. All instruments are placed in a low level console...

The TX telescopic handler range is powered by a 4.5 litre Case turbo engine. All machines are equipped with a low emission Tier III climate friendly engine, that with turbocharging and aftercooling offers from 99 hp to a healthy 118 hp and a powerful 516 Nm Mounted on the side of the machine, the engine is easily accessible for all regular service and maintenance work, with filters and fill points all reached from ground level. Long service intervals and compatibility with the Case electronic service tool [EST] ensure minimum downtime, increasing profitability and keeping your A fully load sensing...

with narrow stabilisers Engine type. Turbo aftercooled, Tier 3, 4 cylinder, 2 valves per cylinder Forward/Reverse speeds Maximum speed on road*' HYDRAULIC SYSTEM Hydraulic controls_ Simultaneous movement. Hydraulic pump_ Hydraulic flow. .Load Sensing Hydraulic pressure. Mast extension_ Fuel tank_ Hydraulic tank * *EPA: Environmental Protection Agency * * * Max. speed limited according to the country's legislations IMPORTANT NOTE: This model is not suitable for manplatform with narrow stabilisers down

without stabilizers with wide stabilizers Engine type. Turbo aftercooled, Tier 3, 4 cylinder, 2 valves per cylinder Forward/Reverse speeds_ Maximum speed on road* * *. HYDRAULIC SYSTEM Hydraulic controls_ Simultaneous movement. Hydraulic pump_ Hydraulic flow_ Hydraulic pressure_ Mast extension_ Fuel tank_ Hydraulic tank .Load Sensing **EPA: Environmental Protection Agency * * * Max. speed limited according to the country's legislations IMPORTANT NOTE: The TX130-45 model is suitable for the use of a Rear axle unlocked

with wide stabilizers Engine type. Turbo aftercooled, Tier 3, 4 cylinder, 2 valves per cylinder Forward/Reverse speeds_ Maximum speed on road* * * _ HYDRAULIC SYSTEM Hydraulic controls_ Simultaneous movement. Hydraulic pump_ Hydraulic flow. _Load Sensing Hydraulic pressure. Mast extension_ Fuel tank_ Hydraulic tank **EPA: Environmental Protection Agency * * * Max. speed limited according to the country's legisletions IMPORTANT NOTE: This model Is suitable for the use of a manplatform with wide stabilizers Machine with stabilizers up

Engine type. Turbo aftercooled, Tier 3, 4 cylinder, 2 valves per cylinder Forward/Reverse speeds Maximum speed on road*' HYDRAULIC SYSTEM Hydraulic controls_ Simultaneous movement, Hydraulic pump_ Hydraulic flow. Hydraulic pressure. Mast extension_ Fuel tank_ Hydraulic tank. _Load Sensing **EPA: Environmental Protection Agency * * * Max. speed limited according to the country's legislations

STANDARD EQUIPMENT & OPTIONS STANDARD EQUIPMENT Design concept I 99hp and 188hp [both turbo aftercooled 4,5 liter 4 cylinder Tier 3) I 3 steering modes ( 2WD 4WD Crab] I Flow sharing / Load sensing hydraulics I Narrow wide or no stabilisers I Front axle balance control I Indipendent stabilisers controls I 2 rear lateral counterweights I Load movement indicator and safety device I Front and rear fenders I Raincup for engine filter I Road light support I Left and right mirrors I Mechanical parking brake I Chain (TX13Q - 33] or Cylinder [others] boom extension I 3 piece (7X130/ 140) or 4 piece [TX170]...