Catalog excerpts
Cement Industry, Open Cast Mining
Open the catalog to page 1Under all conditions In the cement industry, mining and mineral processing machines and equipment are often exposed to extreme working conditions. Besides environmental influences such as dust, humidity and sometimes high temperature variations, both very high and/or shock loads also have to be managed. Machine down time and possible production loss represent an enormous cost factor and since redundant systems are in general not available, the selected lubricant is of major importance. Based on years of experience gathered in close cooperation with leading machine manufacturers special...
Open the catalog to page 2Lubricating greases for roller and plain bearings The very good wear and corrosion protection and the excellent mechanical stability of BECHEM greases allows the reliable mastering of high specific loads as well as influences of dust and moisture even at extended re-lubrication intervals. BECHEM greases proved their excellent performance in: n main bearings of roller presses and crushers n main and pivot bearings of vertical roller mills n pinion and support roller bearings of mills and kilns By the use of newly developed high performance additives n pivot and slewing bearings of excavators...
Open the catalog to page 3High performance oils for closed gear boxes and circulation systems To comply with the increasing demand for a reduction of In gear boxes running with permanent temperatures above power losses and an extension of the oil life time BECHEM 90 ° C synthetic gear oils should be used. The oils of the developed new mineral oil based and synthetic oil based high BERUSYNTH EP and BERUSYNTH GP series offer, compared performance oils. to mineral gear oils, an approximately 4 times longer life time. By using these oils in gear boxes and circulation systems of They additionally exceed the performance...
Open the catalog to page 4Open gear lubricants Technical service BECHEM open gear lubricants ensure a reliable wear protec- tion with simultaneous low consumption by the use of special high performance additives. With those lubricants open gear drives of ■ rotary kilns and coolers ■ hydraulic and bucket wheel excavators and draglines ■ crushers and stacker or reclaimer systems ■ cranes, hoists, winches, drags and spreaders For different requirements concerning temperature, influence of dust or moisture, re-lubrication intervals and lubricant application different product lines with and without solid lubricants can...
Open the catalog to page 5Lubricants for special applications Loose tyres of rotary kilns Chains For the lubrication of the inner and side surfaces of loose A good wear and corrosion protection at round-steel link tyres of rotary kilns a high temperature fluid equipped with a chains of large dimensions are achieved by adhesive semi- special solid lubricant combination is available. It does not fluid greases like those of the BERULIT GA series or high catch fire on hot kiln surfaces and forms only very little smoke. viscous fluids. For small or middle sized conveyor chains with After the evaporation of the synthetic...
Open the catalog to page 6Lubricating greases HIGH LUB FA 50 MO Special grease of very high base oil viscosity with solids for bearings under extreme conditions typical applications: main bearings of roller presses, pivot bearings of vertical roller mills HIGH LUB FA 40 MO Special grease of high base oil viscosity with solids for heavily loaded bearings typical applications: heavy mining machinery, vibrating screens, main bearings of crushers HIGH LUB FA 67 Special greases of different base oil viscosities without solids for heavily loaded bearings typical applications: conveyor systems, main bearings of fans and...
Open the catalog to page 7That’Special! A tradition we are proud of since 1834. This is still today demonstrated by our trademark: the Rhus Flower. After permanent d evelopment, BECHEM is today a »Global Player«. BECHEM special lubricants, industrial lubricants, metal working fluids and solutions for forming technology are based on our e xtensive experience in the development of special chemistry and on the latest tribologic knowledge. Our know-how with regard to friction, wear and lubrication always takes account of our customers’ requirements for economical and ecological optimisation. We feel obliged to...
Open the catalog to page 8All CARL BECHEM catalogs and technical brochures
-
Biodegradable lubricants
10 Pages
-
Divers
16 Pages
-
Semi hot/ hot forging
4 Pages
-
Fitting lubrication
6 Pages
-
Anti-Friction-Coatings
12 Pages
-
Deep drilling oils
4 Pages
-
Cutting and grinding oils
4 Pages
-
Coolant lubricants
6 Pages
-
Corrosion protection oils
4 Pages
-
GREEN LUBRICANTS
4 Pages
-
Chain Oil
5 Pages
Archived catalogs
-
Forming technology
4 Pages
-
Anti Friction Coatings
4 Pages
-
Metal working
4 Pages
-
Special Lubrificants
4 Pages
-
Industrial Lubrificants
4 Pages