Catalogs >
CAMOZZI AUTOMATION >
Series DRCS drive for stepper motors EN

Series DRCS drive for stepper motors EN
8Pages

Add to favorites

Catalog excerpts

SERIES DRCS DRIVE FOR STEPPER MOTORS

Open the catalog to page 1

SERIES DRCS SMART DRIVE FOR STEPPER MOTORS CAN BE CONTROLLED IN FREQUENCY (STEP AND DIRECTION), DIGITAL I/O, AND CANOPEN CAN BE USED WITH STEPPER MOTORS UP TO SIZE NEMA 34 CONFIGURATION THROUGH HARD WIRED AND WIRELESS LAN CONNECTIONS The Series DRCS drives, compact and optimised The use of micro-stepping control (up to 1/128 steps) in one size, have been specially configured for enables the drive to almost replicate a sinusoidal all small and medium-sized Camozzi stepper motors. current while considerably reducing the natural They are capable of controlling stepper motors resonance of the...

Open the catalog to page 2

Series DRCS drive for stepper motors EN - 3

Serie DRCS / Drive for stepper motors Each command can be absolute or relative. Through the Step and Direction commands, it WLAN BL-BLE is possible to control the drive in frequency mode. The frequency defines the speed, while the number of steps defines the position. The Series DRCS drives are equipped with serial protocols CANopen CiA 301 and CiA 402 through which it is possible to perform motion control and condition monitoring of the drive. To configure the drive, wired (USB 2.0) or wireless WLAN connections can be used. Thanks to an innovative system that takes advantage of Near Field...

Open the catalog to page 3

Series DRCS drive for stepper motors EN - 4

Data ingestion & Data mining IIoT gateway DIAGNOSTIC CHARACTERISTICS ON/OFF time Run time (working hours) Health status Series D Valve island Cycle counter Power consumption Series PRE Pressure regulator Series DRCS Drive for motors Data management Camozzi Digital

Open the catalog to page 4

Series DRCS drive for stepper motors EN - 5

Serie DRCS / Drive for stepper motors General data SUPPLY VOLTAGE Logic CURRENT Current Holding current automatic reduction of the holding current with motor in stop mode, this function can be set according to the holding current or its delay AMBIENT Operating temperature 0 ÷ 40°C (up to 55°C with forced ventilation) Storage temperature overvoltage, minimum voltage, overtemperature, short-circuit or grounding on the motor Control method Amplification type dual H-Bridge, 4 Quadrants Position control encoder 100 a 5000 differential impulses / revolution DIGITAL I/O Input control signal Output...

Open the catalog to page 5

Series DRCS drive for stepper motors EN - 6

Coding example DRCS COMMUNICATION: D = digital I/O and impulse frequency C = CANopen, Digital I/O and impulse frequency VERSIONS: A = standard B = WLAN BL-BLE Series DRCS drives Logic supply Power supply Digital I/O and impulse frequency CANopen, Digital I/O and impulse frequency Digital I/O and impulse frequency WLAN BL-BLE CANopen, Digital I/O and impulse frequency WLAN BL-BLE

Open the catalog to page 6

Series DRCS drive for stepper motors EN - 7

Serie DRCS / Drive for stepper motors Cables and accessories Cable for Series DRCS drive with brake Cable for Series DRCS drive without brake Motor cable for Series DRCS drive without brake (Nema 34 only) Encoder cable for Series DRCS drive Cable for Series DRCS drive logic supply Cable for Series DRCS drive power supply Cable for Series DRCS drive CANopen Cable for Series DRCS drive CANopen expansion CAN terminating resistor for Series DRCS drives Mounting brackets for DIN rail

Open the catalog to page 7

Series DRCS drive for stepper motors EN - 8

Camozzi Automation S.p.A. Società Unipersonale Via Eritrea, 20/I 25126 Brescia Italy Tel. +39 030 37921 info@camozzi.com Customer Service Tel. +39 030 3792790 service@camozzi.com Export Department Tel. +39 030 3792255 sales@camozzi.com A Camozzi Group Company

Open the catalog to page 8