- Catalogs
- Cablecraft Motion Control
- Brake Lever Over Center Locking Hand Control
Brake Lever Over Center Locking Hand Control
Brake Lever Over Center Locking Hand Control
- Heat-treated 4130 load link for durability.
- Adjustable knob for setting initial cable tension and travel.
- Optional tamper-resistant knob and weather-resistant switch.
- Supports loads up to 1,000 lb with a travel range of 2-7/16” maximum.
- Materials include nylon-covered innermember, plastic-covered conduit, and stainless steel.
- Dimension A is used for calculating cable length in the 'OFF' position.
- Dimension B minimum is for the 'ON' position with minimum travel, while B maximum is for maximum travel.
- Various kits (B815, B816, B817, B834, B835, B837) are supplied with necessary hardware for installation, including clevis pins, cotter pins, washers, and mounting spacers.
- Side Mount and Flange Mount configurations are available, with specific kits for each type.
- Side Mounts are suitable for cowl, instrument panel, seat riser, or frame installations.
- Flange Mounts are designed for bulkhead, floor, or island installations, maintaining alignment for improved component life.
Catalog excerpts
Over Center Locking Hand Control Cablecraft® park brake levers offer superior performance, quality and service life to both the designer and user. • Two distinct lever positions - Over center and off, which are approximately 90° apart • No ratcheting to limit travel or secondary unlocking required for operation • Heat-treated 4130 load link provides durability and reliability • Adjusting knob allows for setting the initial cable tension, travel, and compensates for system wear • Adaptable with side or flange mount configurations • Input lever and side plates have an epoxy finish or electro-static p and all other components are coated for corrosion resistance • Optional tamper-resistant knob to inhibit unauthorized adjustment • Optional weather-resistant switch at the off position • Supplied with hardware necessary to attach the cable end fittings to the load link • Loads of up to 1,000 lb. • Travel range is 2-7/16" maximum Material: • Nylon covered innermember • Plastic covered conduit • Stainless steel Cablecraft® Lever Innermember Conduit Fitting Fitting 1. Dimension A is with the lever in full "OFF" position. Use dimension A in calculating cable length. 2. Dimension B minimum is with the lever in full "ON" position and adjusted for minimum (CCW) travel. Use dimension B minimum during installation and initial adjustment. Turn knob (CW) to add travel and increase brake pressure setting. 3. Dimension B maximum is with the lever in full "ON" position and adjusted for maximum (CW) travel.
Open the catalog to page 1
Brake Lever Side Mount 165-508-008 2.5 inches (64mm) wide side plates; one cable, with three alternate sets of cable clamp holes. For cowl, instrument panel, seat riser or frame installation. Kit B815 — supplied with the following hardware: Clevis pin Cotter pin Washer Mounting spacers (2) Cable clamp Clamp base Clamp spacers (2) .343 DIA 6 PLACES THRU BOTH WALLS .390 DIA 2 PLACES THRU BOTH WALLS Side Mount 165-508-009 2.5 inches (64mm) wide side plates; one cable. For cowl, instrument panel, seat riser or frame installation. No cable support. Kit B816 — supplied with the following hardware:...
Open the catalog to page 2
Side Mount 165-508-011 1.5 inches (38mm) wide side plates; one cable. For cowl, instrument panel, seat riser or frame installation. Kit B834 — supplied with the following hardware: Clevis pin Cotter pin Washer Mounting spacers (2) Cable clamp Side Mount 165-508-013 2.5 inches (64mm) wide side plates; two cables. For cowl, instrument panel, seat riser or frame installation. NOTE: When considering load requirements, the load on the lever assembly will be the sum of the load in each cable. Kit B835 — supplied with the following hardware: Clevis pins (2) Cotter pins (2) Washers (2) Mounting spacers...
Open the catalog to page 3
Brake Lever Side Mount 165-508-028 1.5 inches (38mm) wide side plates; one cable. For cowl, instrument panel, seat riser or frame installation. Kit B837 — supplied with the following hardware: Clevis pin Cotter pin Washer Mounting spacers (2) Cable clamp Clamp spacers (2) 4 HOLES THRU BOTH WALLS FOR .312 DIA BOLTS Flange Mount 165-508-078 2.5 inches (64mm) wide side plates; two cables. For bulkhead, floor or island (doghouse) installation. NOTE: When considering load requirements, the load on the lever assembly will be the sum of the load in each cable. Wing flange mounting. Kit B835 — supplied...
Open the catalog to page 4All Cablecraft Motion Control catalogs and technical brochures
Throttle Pedal – Heavy Duty2 Pages
Pull-Only Tension Controls2 Pages
Connecting a World in Motion84 Pages
Push-Pull Standard4 Pages
Micro Adjust Control Heads2 Pages
Non-Lock Control Heads2 Pages
Twist Lock Industrial2 Pages
Cablecraft Linkage4 Pages
High-Temp Rod Ends/Linkages4 Pages
Unidrum Lever4 Pages
Push-Pull 4B4 Pages
SR-G Ball Joints2 Pages
COM-P Sperical Bearings2 Pages
Leverstak2 Pages
Micro Adjust Industrial2 Pages
Button Lock Performance2 Pages
Pull-Only T-Flex2 Pages
Pull-Only Tension Cables2 Pages
R-G Ball Joints2 Pages
J/JM Sperical Bearings2 Pages
DBM and DBF Rod Ends2 Pages
Archived catalogs
DC/DH Control Swivels2 Pages
Manual Transmission Shifter4 Pages
Hardware_End4 Pages
Hardware/ End Fittings4 Pages
Turbo & EGR Platforms & Beyond12 Pages
Button Lock2 Pages
Pull-Only Clutch4 Pages
Push-Pull Cable - 4B4 Pages
Pull-Only Cable - T-Flex2 Pages
Pull-Only Cable - Tension2 Pages
Pull-Only Clutch Cable4 Pages
Custom Linkage Assemblies2 Pages
Performance Push-Pull Cable2 Pages
DBM/DBF2 Pages
Custom Cable Assemblies2 Pages
Hardware/End Fittings4 Pages
Custom Hand Controls4 Pages
Leverstack Hand Control2 Pages
Unidrum Lever - METRIC4 Pages
Undidrum Lever4 Pages
Light Duty Lever2 Pages
Brake Lever4 Pages
Pull-Only Brake Cable4 Pages
Push-Pull Cable - Standard4 Pages
Linkage Assemblies - Custom2 Pages
