Catalog excerpts
OPERATION MANUAL USB Sensor Interface Model 9206 ©2024 burster praezisionsmesstechnik gmbh & co kg All rights reserved Manufacturer: burster praezisionsmesstechnik gmbh & co kg TalstraGe 1 - 5 P.O.Box 1432 Germany Germany E-Mail info@burster.com www.burster.com
Open the catalog to page 1USB Sensor Interface Model 9206 Warranty - exclusion of liability All information in the present documentation was prepared and compiled with great care and reproduced subject to effective control measures. No warranty is provided for freedom from errors. We reserve the right to make technical changes. The present information as well as the corresponding technical data can change without notice. Reproduction of any part of this documentation or its processing or revision using electronic systems is prohibited without the manufacturer's prior written approval. Components, devices and...
Open the catalog to page 2USB Sensor Interface Model 9206The measurement solution. EU-Konformitstserklarung (nach en iso/iec i 7050-1:2010) EU-Declaration of conformity (in accordance with EN ISO/IEC 17050-1:2010) Name des Ausstellers: Issuer’s name: burster prazisionsmesstechnik grnbh & co kg Anschrift des Ausstellers: Issuer’s address: Gegenstand der Erklarung: Object of the declaration: Talstr. 1-5 76593 Gernsbach, Germany USB-(Multi)Sensor-lnterface USB-(Multi) Sensor-Interface Modellnummer(n) (Typ): Model number/type: Diese Erklarung beinhaltet obengenannte Produkte mit alien Optionen This declaration covers...
Open the catalog to page 3USB Sensor Interface Model 9206 USB Multisensor-Interface desktop unit (IP20)
Open the catalog to page 4USB Sensor Interface Model 9206 Warning! The following instructions must be followed to prevent electric shock and injuries: Follow all equipment safety procedures. Only use the device outside from explosive areas. Only use the device when it is undamaged. Do not apply more than the rated voltage. See specifications for supported ranges. Any repairs that may be needed must be performed only at the manufacturer's premises. Caution! The following points must be followed to prevent injuries and damage to property: Do not use any cleaning agents that contain organic solvents or...
Open the catalog to page 5USB Sensor Interface Model 9206
Open the catalog to page 67.4 Adjustment of a transmitter having a voltage output using the teach-in method ... 56
Open the catalog to page 7USB Sensor Interface Model 9206 1. The model 9206 USB Sensor Interface is intended for the acquisition and processing of sensor signals. The model 9206 USB Sensor Interface is a user-configurable single-channel device, or optionally a multi-channel device housed in a desktop unit. The device is configured via the USB port. The model 9206 USB Sensor Interface is ideally suited to measuring mechanical variables such as force, torque, pressure, acceleration, displacement and angle. It makes acquisition and processing of straingage, potentiometric and standard signals straightforward. Signal...
Open the catalog to page 9USB Sensor Interface Model 9206 1.1 Normal use The model 9206 USB Sensor Interface has been developed specifically for high-speed measurements, and therefore covers a huge range of applications. Designed for use with a variety of analog sensors, the device can capture a huge range of output signals for conditioning in mobile systems. Industry-compatible connection and installation technologies make it easier for the user to adapt and integrate the unit in existing mechanical and electrical environments. The outstanding measuring quality combined with a large number of values used for...
Open the catalog to page 10USB Sensor Interface Model 9206 1.2.3 Factory warranty burster praezisionsmesstechnik gmbh & co kg provides a manufacturer's warranty for a period of 24 months after delivery. Any repairs required during this time will be made without charge. Damage caused by improper use of the device is not covered by the warranty. If the device needs to be returned for repairs, please note the following requirements for packing and shipping: • If you have a problem with the device, please attach a note to the case summarizing the fault. • The technical data can change at any time without notification. We...
Open the catalog to page 11USB Sensor Interface Model 92062. Preparation2.1 Unpacking The unit is packaged for protection against shock during shipment. > Carefully unpack the unit and verify that all items are present. > Inspect the instrument carefully for damage. If you suspect that the unit has been damaged during shipping, notify the delivery company immediately. The packaging should be retained for examination by a representative of the manufacturer and/or the delivery company. The model 9206 USB Sensor Interface must be shipped only in its original packaging provided by us or in a container capable of...
Open the catalog to page 12USB Sensor Interface Model 9206 2.3.1 Opening the 9206 tubular housing Caution! Risk of damage! Before opening the tubular housing always undo both PG cable glands. Before opening or closing the tubular housing, isolate the 9206 from the power supply. For the in-line 9206 model, all controls and connections are located inside the tubular housing. Finely knurled end-fitting coarsely knurled end-fitting One of the end fittings is coarsely knurled. How to open the tubular housing Undo the PG cable glands at both ends of the tubular housing. By doing this you reduce the risk of damaging the...
Open the catalog to page 13USB Sensor Interface Model 9206 Once the housing is unscrewed from the end fittings, the circuit board is exposed. The In Line unit of the model 9206 USB Sensor Interface has IP67 degree of protection. The module is therefore protected from the effect of temporary immersion in water and accessing dangerous components using a wire of diameter ≥ 1.0 mm. The desktop unit has IP20 degree of protection. Ambient temperature The permitted ambient temperature range for the model 9206 USB Sensor Interface during operation is -20 °C to +60 °C. The device can be stored at temperatures between -40 °C...
Open the catalog to page 14USB Sensor Interface Model 9206 2.6 Connection via screw-terminals The screw terminals located on the circuit board of the 9206 USB Sensor Interface are listed in the figure below. Diagram 3: Screw terminals and pin assignments Diagram 4: Solder bridges The solder bridges must be closed as shown. Only applies to tubular housing model.
Open the catalog to page 15All Burster präzisionsmesstechnik gmbh & co kg catalogs and technical brochures
-
SENSOR SOLUTIONS
1 Pages
-
A CONNECTION THAT NETWORKS
1 Pages
-
Quality leading the way
3 Pages
-
Data-Sheet - 9251
6 Pages
-
Data Sheet Model 9210
5 Pages
-
Flyer Load Experts
1 Pages
-
Load cells
25 Pages
-
Data Sheet 8427
7 Pages
-
Displacement Sensors
2 Pages
-
Displacement Sensors
2 Pages
-
Data Sheet Typ 87240
2 Pages
-
Data sheet Typ 8416
6 Pages
-
Load cells
25 Pages
-
Data Sheet Model 8402
6 Pages
-
Flyer Load Experts
1 Pages
-
Data Sheet - Model 8438
6 Pages
-
Data Sheet Model 8400-B001
2 Pages
-
Sensor Solutions
1 Pages
-
A Connection that Networks
1 Pages
-
Qualitiy leading the way
3 Pages
-
Data Sheet Model 9250
7 Pages
-
Torque Sensors
9 Pages
-
Data Sheet Typ 8656
7 Pages
-
Data Sheet Model 9235
2 Pages
-
Data sheet Model 8435
7 Pages
-
Data Sheet Typ 8417
7 Pages
-
Data Sheet Typ 8532
2 Pages
-
Torque Sensors
9 Pages
-
Data Sheet Typ 8627
2 Pages
-
Data Sheet Model 8527
7 Pages
-
Data Sheet Model 8526
9 Pages
-
Data Sheet Typ 8655
7 Pages
-
Data Sheet Model 8431
12 Pages
-
Pressfitting -the reliable way
11 Pages
-
Data Sheet Typ 9311
6 Pages
-
Data Sheet Model 8511
6 Pages
-
Data Sheet - DIGISTANT® 4463
5 Pages
-
Data sheet Series 8738
2 Pages
-
Torque Sensors
16 Pages
-
Data Sheet Model 8630
6 Pages
-
Data Sheet Typ 8625
7 Pages
-
Data Sheet Models 8710, 8711
2 Pages
-
Data Sheet Typ 8740/8741
4 Pages
-
Data Sheet Models 8712, 8713
2 Pages
-
Load-cell
25 Pages
-
Data Sheet Motel 8451
7 Pages
-
Procision to the core
3 Pages
-
Flyer Battery Tester
1 Pages
-
Data Sheet Model 2560
5 Pages
-
Data Sheet Model 8561
6 Pages
-
Data Sheet Model 2311
5 Pages
-
Data Sheet Model 8523
8 Pages
-
Data Sheet Series 87350
2 Pages
-
Data Sheet Model 9243
2 Pages
-
Data Sheet Typ 8739
2 Pages
-
Load-cell
25 Pages
-
Data Sheet Motel 8565
5 Pages
-
Data sheet Model 8631
5 Pages
-
Data Sheet Model 8718
2 Pages
-
Data Sheet Typ 8512
5 Pages
-
Data-Sheet- Model 8228
6 Pages
-
Data Sheet Model 8510
5 Pages
-
Data Sheet Model 8415
6 Pages
-
Data Sheet Model 2511
6 Pages
-
RESISTOMAT® Model 2329
4 Pages
-
Data Sheet Model 8524
8 Pages
-
Data Sheet Model 2550
4 Pages
-
Data Sheet Model 9186/8532
2 Pages
-
Data Sheet Typ 8645
5 Pages
-
Data sheet Model 8709
2 Pages
-
Flyer Displacement Sensor
2 Pages
-
Data Sheet - Model 8670
4 Pages