Catalog excerpts
OPERATION MANUAL Torque Sensor Model 8656 burster praezisionsmesstechnik gmbh & co kg All rights reserved Valid from Manufacturer: burster praezisionsmesstechnik gmbh & co kg Talstr. 1 - 5 Talstr. 1 - 5 76593 Gernsbach 76593 Gernsbach Germany Germany Tel.: +49-7224-645-0 Fax.: +49-7224-645-88 Email: info@burster.com www.burster.com 4357-BA8656EN-5699-021525
Open the catalog to page 1Warranty disclaimer All information in the present documentation was prepared and compiled with great care and reproduced subject to effective control measures. No warranty is provided for freedom from errors. We reserve the right to make technical changes. The present information as well as the corresponding technical data can change without notice. Reproduction of any part of this documentation or its processing or revision using electronic systems is prohibited without the manufacturer‘s prior written approval. Components, devices and measured value sensors made by burster...
Open the catalog to page 2The following symbols on the torque sensor model 8656 and in this operation manual warn of hazards. Symbols used in this manual 1.1.1. Signal words The following signal words are used in the operation manual according to the specified hazard classification. DANGER High degree of risk: indicates a hazardous situation which, if not avoided, will result in death or serious injury WARNING Moderate degree of risk: indicates a hazardous situation which, if not avoided, may result in death or serious injury. CAUTION Low degree of risk: indicates a hazardous situation which, if not avoided, could...
Open the catalog to page 6General safety instructions The torque sensor model 8656 uses state-of-the-art engineering and is safe to operate. However, if thetorque sensor model 8656 is not used or operated as intended, it may present a hazard. DANGER Danger of electric shock! The following instructions must be followed to prevent electric shock and injuries: • In order to achieve high measuring characteristic value, the torque sensor model 8656 is not designed with the usual safety factors (2…20) for machine designs. For applicable overload factors, see the technical data (data sheet). • Observe accident prevention...
Open the catalog to page 7IMPORTANT: Read the operation manual carefully before using the equipment, and keep for future reference Bestimmungsgemäßer Gebrauch The torque sensor model 8656 measures static and dynamic torques on rotating or stationary machine parts in either direction of rotation. You have the option of measuring rotational speed or angular displacement. The respective upper range value is shown on the type plate. For the dual-range sensor, the larger full-scale value is given. The USB version of the 8656 torque sensor model 8661 transmits all measurement signals via USB. Both the low mass of the...
Open the catalog to page 8Environmental conditions • Avoid radiant heat or cooling from one side. • Protect the torque sensor model 8656 from moisture. • The torque sensor model 8656 is not resistant to the effects of chemicals. Do not use the torque sensor model 8656 in a corrosive environment. • Keep the bearings and connectors free of dust, dirt and other foreign matter. 2.3.1. Storage conditions Use clean packaging to package the torque sensor model 8656. The torque sensor model 8656 must be stored under the following conditions: • Dry atmosphere • No condensation • Temperature between +0 °C and +60 °C DANGER...
Open the catalog to page 9Scope of delivery • Torque sensor model 8661 • Mating connector • Operation manual • Data sheet • Optional: USB cable DANGER Electric shock hazard! Never connect up the torque sensor model 8656 if it shows signs of damage incurred in transit. Only ever use the torque sensor model 8656 under the conditions specified in this operation manual. Inspect the torque sensor model 8656 carefully for damage. If you suspect that the torque sensor model 8661 has been damaged during shipping, notify the delivery company within 72 hours. The packaging should be retained for examination by a...
Open the catalog to page 10Conversions and modifications f you open or dismantle the torque sensor model 8656 during the warranty period, this will void the warranty immediately. The torque sensor model 8656 does not contain any parts that are intended to be serviced by the user. Only the manufacturer's own qualified personnel are permitted to open the torque sensor model 8656. It is forbidden to make any modification to the torque sensor model 8656 without our written permission. We cannot accept liability in the event of such action. Our recommendations • Check the bearings at least once a year to see that they...
Open the catalog to page 11Test side The test side is that end of the shaft at which you apply the torque being measured to the torque sensor model 8656. This side normally has the smallest moment of inertia. You will see these markings on the measurement end of the torque sensor model 8656: Test side torque sensor model 8656 Drive side The drive side is the opposite end to the measurement end. The torque sensor model 8656 is also mechanically connected at this side. This side normally has the larger moment of inertia. You will see these markings on the drive side of the torque sensor model 8656: Drive side torque...
Open the catalog to page 12You can use the torque sensor model 8656 to measure both clockwise and counterclockwise torques. If the torque is exerted in an anticlockwise direction (looking at the measurement end), you will get a negative signal at the output. Sign convention for measuring angular displacement If the sensor shaft rotates clockwise (looking at the drive end), channel A leads channel B by 90°. If the sensor shaft rotates anticlockwise (looking at the drive end), channel B leads channel A by 90°. Static and quasi-static torques Static and quasi-static torques change their value only slowly or not at all....
Open the catalog to page 13Device design and general information Specifications as full dimensions, mass and power depend on the version of the torque sensor model 8656. Please refer to the data sheet for specifications. Mechanical design Design principle torque sensor 8656 The torque sensor model 8656 essentially consists of three elements: • Measuring shaft • Electronic box • Case The measuring shaft is composed of torsion bar, strain gauges, instrumentation amplifier and power and signal transmission components. If the torque sensor model 8656 is fitted with the rotational speed or angular displacement option, an...
Open the catalog to page 14All Burster präzisionsmesstechnik gmbh & co kg catalogs and technical brochures
-
Torque Sensors
9 Pages
-
Data Sheet Typ 8656
7 Pages
-
Data Sheet Typ 8655
7 Pages
-
Press fitting - the reliable way
11 Pages
-
Data Sheet Typ 9307
6 Pages
-
Data Sheet Model 2511
6 Pages
-
Data Sheet Typ 8625
7 Pages
-
Data Sheet Model 9243
2 Pages
-
Data Sheet- Model 2500
2 Pages
-
SENSOR SOLUTIONS
1 Pages
-
A CONNECTION THAT NETWORKS
1 Pages
-
Quality leading the way
3 Pages
-
Data-Sheet - 9251
6 Pages
-
Data Sheet Model 9210
5 Pages
-
Flyer Load Experts
1 Pages
-
Data Sheet 8427
7 Pages
-
Displacement Sensors
2 Pages
-
Displacement Sensors
2 Pages
-
Data Sheet Typ 87240
2 Pages
-
Data sheet Typ 8416
6 Pages
-
Load cells
25 Pages
-
Data Sheet Model 8402
6 Pages
-
Flyer Load Experts
1 Pages
-
Data Sheet - Model 8438
6 Pages
-
Data Sheet Model 8400-B001
2 Pages
-
Sensor Solutions
1 Pages
-
A Connection that Networks
1 Pages
-
Qualitiy leading the way
3 Pages
-
Data Sheet Model 9250
7 Pages
-
Data Sheet Model 9235
2 Pages
-
Data sheet Model 8435
7 Pages
-
Data Sheet Typ 8417
7 Pages
-
Data Sheet Typ 8532
2 Pages
-
Torque Sensors
9 Pages
-
Data Sheet Typ 8627
2 Pages
-
Data Sheet Model 8527
7 Pages
-
Data Sheet Model 8526
9 Pages
-
Data Sheet Model 8431
12 Pages
-
Data Sheet Typ 9311
6 Pages
-
Data Sheet Model 8511
6 Pages
-
Data Sheet - DIGISTANT® 4463
5 Pages
-
Data sheet Series 8738
2 Pages
-
Torque Sensors
16 Pages
-
Data Sheet Model 8630
6 Pages
-
Data Sheet Models 8710, 8711
2 Pages
-
Data Sheet Typ 8740/8741
4 Pages
-
Data Sheet Models 8712, 8713
2 Pages
-
Load-cell
25 Pages
-
Data Sheet Motel 8451
7 Pages
-
Procision to the core
3 Pages
-
Flyer Battery Tester
1 Pages
-
Data Sheet Model 2560
5 Pages
-
Data Sheet Model 8561
6 Pages
-
Data Sheet Model 2311
5 Pages
-
Data Sheet Model 8523
8 Pages
-
Data Sheet Series 87350
2 Pages
-
Operation manual
76 Pages
-
Data Sheet Typ 8739
2 Pages
-
Load-cell
25 Pages
-
Data Sheet Motel 8565
5 Pages
-
Data sheet Model 8631
5 Pages
-
Data Sheet Model 8718
2 Pages
-
Data Sheet Typ 8512
5 Pages
-
Data-Sheet- Model 8228
6 Pages
-
Data Sheet Model 8510
5 Pages
-
Data Sheet Model 8415
6 Pages
-
RESISTOMAT® Model 2329
4 Pages
-
Data Sheet Model 8524
8 Pages
-
Data Sheet Model 2550
4 Pages
-
Data Sheet Model 9186/8532
2 Pages
-
Data Sheet Typ 8645
5 Pages
-
Data sheet Model 8709
2 Pages
-
Flyer Displacement Sensor
2 Pages
-
Data Sheet - Model 8670
4 Pages