Catalogs >
burster präzisionsmesstechnik gmbh & co kg >
Operating Manual DIGIFORCE® Model 9311

Operating Manual DIGIFORCE® Model 9311
216Pages

Catalog excerpts

Operating Manual DIGIFORCE® Model 9311 - 1

OPERATION MANUAL DIGIFORCE® Model 9311 © 2018 burster praezisionsmesstechnik gmbh & co kg All rights reserved Manufacturer: burster praezisionsmesstechnik gmbh & co kg Talstr. 1 - 5 P.O. Box 1432 Germany Germany Tel.: +49-7224-645-0 Fax: +49-7224-645-88 Email: info@burster.com www.burster.com

Open the catalog to page 1

Operating Manual DIGIFORCE® Model 9311 - 2

Warranty disclaimer All information in the present documentation was prepared and compiled with great care and reproduced in accordance with effective control measures. This documentation may contain errors, and the information it contains and the corresponding technical data are subject to change without notice. Reproduction of any part of this documentation or its processing or revision using electronic systems is prohibited without the manufacturer's prior written approval. Components, devices and measurement sensors made by burster praezisionsmesstechnik (hereinafter referred to as the...

Open the catalog to page 2

Operating Manual DIGIFORCE® Model 9311 - 3

The measurement solution. EU-Konformitatserklarung (nach en iso/iec 17050-1:2010) EU-Declaration of conformity (in accordance with EN ISO/IEC 17050-1:2010) Name des Ausstellers: Issuer’s name: Anschrift des Ausstellers: Issuer’s address: Gegenstand der Erklarung: Object of the declaration: burster prazisionsmesstechnik gmbh & co kg Talstr. 1-5 76593 Gernsbach, Germany DIGIFORCE®X/Y-Monitoring, Einpress-, Fijge-, Niet- und Verstemmuberwachung DIGIFORCE® X/Y-Monitoring, press-fit Joining, rivet and caulking monitoring DIGIFORCE® 9311 Modellnummer(n) (Typ): Model number /type: Diese Erklarung...

Open the catalog to page 3

Operating Manual DIGIFORCE® Model 9311 - 9

® The following symbols on the DIGIFORCE 9311 and in this operation manual warn of hazards. 1.1 Symbols used in the instruction manual 1.1.1 Signal words The following signal words are used in the operation manual according to the specified hazard classification. DANGER High degree of risk: indicates a hazardous situation which, if not avoided, will result in death or serious injury. A WARNING Moderate degree of risk: indicates a hazardous situation which, if not avoided, may result in death or serious injury. A CAUTION Low degree of risk: indicates a hazardous situation which, if not...

Open the catalog to page 9

Operating Manual DIGIFORCE® Model 9311 - 11

2 Introduction IMPORTANT: Read the operation manual carefully before using the equipment, and keep for future reference. ® The DIGIFORCE 9311 is an instrument that is designed to monitor repetitive production processes. Its core function is to record and analyse process signals representing physical variables between which there is a defined relationship, for instance recording a curve of force, pressure or torque plotted against displacement, angle or time. Graphical evaluation elements such as windows, trapezoids, thresholds or envelopes are used to analyse the resultant curve. The...

Open the catalog to page 11

Operating Manual DIGIFORCE® Model 9311 - 12

2.4 Ambient conditions 2.4.1 Storage conditions The following requirements must be met when storing the DIGIFORCE 9311: • Store at temperatures between 0 °C and +60 °C • The unit must be packed in clean packaging • Store in a dry environment • No condensation 2.4.2 Operating conditions The following requirements must be met when operating the DIGIFORCE 9311: • Always operate indoors • Maximum height above sea level 2000 m • Operate at temperatures between +5 °C and +40 °C, ideally +23 °C • Humidity: 80% up to +31 °C, decreasing linearly above that temperature to 50% at Tmax, no condensation...

Open the catalog to page 12

Operating Manual DIGIFORCE® Model 9311 - 13

DANGER Electrical shock hazard Disconnect the DIGIFORCE® 9311 from the power plug before cleaning. ® Disconnect the DIGIFORCE 9311 from the power plug and use a slightly damp cloth for cleaning the unit. NOTICE ® Do not immerse the DIGIFORCE 9311 in water or hold it under running water. Do not use strong cleaning agents as these may damage the instrument. Use a slightly damp cloth to clean the instrument. 2.5 Personnel Personnel must be familiar with the relevant regulations. They must follow these regulations. Only trained personnel who are familiar with the applicable safety regulations...

Open the catalog to page 13

Operating Manual DIGIFORCE® Model 9311 - 14

DANGER Electrical shock hazard Never switch on the instrument if it shows signs of damage incurred in transit. Only ever use the instrument under the conditions specified in this operation manual. Inspect the instrument for damage. If you suspect that the unit has been damaged during shipping, notify the delivery company within 72 hours. ® The DIGIFORCE 9311 should be shipped only in its original packaging or in packaging capable of providing an equivalent degree of protection. burster praezisionsmesstechnik gmbh & co kg provides a manufacturer's warranty for a period of 24 months after...

Open the catalog to page 14

Operating Manual DIGIFORCE® Model 9311 - 15

2.10 Error messages when the unit is powered up ® During boot-up, the DIGIFORCE 9311 may display certain error messages. The following errors mean that the DIGIFORCE® 9311 must be sent in for checking and possibly repair: For further information, please refer to section 2.2 "Customer Service" on page 11.

Open the catalog to page 15

Operating Manual DIGIFORCE® Model 9311 - 16

3 Principles of design and operation ® Please refer to the DIGIFORCE 9311 data sheet for full details of dimensions, weight, degree of protection etc. 3.1 Range of functions The DIGIFORCE® 9311 monitors processes in which precisely defined functional relationships need to be demonstrated between two measured quantities. These measured quantities are recorded synchronously during the manufacturing process or subsequent functional testing to produce a measurement curve, which is then assessed using graphical evaluation elements. After evaluating the measurements, the instrument displays the...

Open the catalog to page 16

Operating Manual DIGIFORCE® Model 9311 - 17

3.3 Power supply The instrument can be operated with a voltage of 100 to 240 VAC (±10 %) / 50 to 60 Hz (±10 %) / typical 15 VA. A DANGER Inspect the power lead for damage before use. Do not connect the power lead if there are signs of damage. To help identify damage to the power lead in good time, test it regularly in accordance with national accident prevention regulations. 3.4 Sensors suitable for use with the instrument ® The DIGIFORCE 9311 can process signals from a huge range of sensor technologies. Note: The "Channel settings" menu (M21) is where the physical connectors, and hence the...

Open the catalog to page 17