Catalogs >
burster präzisionsmesstechnik gmbh & co kg >
Operating Manual DIGIFORCE® model 9307

Operating Manual DIGIFORCE® model 9307
217Pages

Catalog excerpts

Operating Manual DIGIFORCE® model 9307 - 1

Operating Manual DIGIFORCE® model 9307 - 2

Warranty disclaimer All information in the present documentation was prepared and compiled with great care and reproduced in accordance with effective control measures. This documentation may contain errors, and the information it contains and the corresponding technical data are subject to change without notice. Reproduction of any part of this documentation or its processing or revision using electronic systems is prohibited without the manufacturer's prior written approval. Components, devices and measurement sensors made by burster praezisionsmesstechnik (hereinafter referred to as the...

Open the catalog to page 2

Operating Manual DIGIFORCE® model 9307 - 6

Connector C: Connection guidance for incremental sensors ... 49

Open the catalog to page 6

Operating Manual DIGIFORCE® model 9307 - 8

Additional results when recording two curves Y1(x) and Y2(x)123 Additional results when recording two curves Y1(x) and Y2(x)130 Additional results when recording two curves Y1(x) and Y2(x)137

Open the catalog to page 8

Operating Manual DIGIFORCE® model 9307 - 9

Parameters in „Sensor test“ for channel X, Y1 und Y2 menu (menu 36)170 Changing the measurement program without program acknowledgement198 Changing the measurement program with program acknowledgement 199

Open the catalog to page 9

Operating Manual DIGIFORCE® model 9307 - 10

Switching signals for channel “X“ with ABSOLUTE reference205 Switching signals for channel “X“ with TRIGGER reference .. 206

Open the catalog to page 10

Operating Manual DIGIFORCE® model 9307 - 11

The following symbols on the DIGIFORCE 9307 and in this operating manual warn of hazards. Symbols used in this manual Signal words The following signal words are used in the operating manual according to the specified hazard classification. DANGER High degree of risk: indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Moderate degree of risk: indicates a hazardous situation which, if not avoided, may result in death or serious injury. CAUTION Low degree of risk: indicates a hazardous situation which, if not avoided, could result in minor...

Open the catalog to page 11

Operating Manual DIGIFORCE® model 9307 - 12

Symbols and precautionary statements on the DIGIFORCE® 9307 Description Hazard warning Disconnect the power plug before opening – Follow safety instructions – Professional servicing only. Electrostatic discharge. Do not touch! Electrostatic discharge can damage the piezoelectric connector (F). Take precautionary measures to prevent a static discharge at connector F. Warning ! To prevent electrical shock do not open device. To prevent fire replace only with same type and rating of fuse ! Warning of electrical shock hazard. ® Warning of fire hazard. Always replace the fuse with a fuse of the...

Open the catalog to page 12

Operating Manual DIGIFORCE® model 9307 - 13

IMPORTANT: Read the operating manual carefully before using the equipment, and keep for future reference. The DIGIFORCE 9307 is an instrument for monitoring repetitive production processes. Its core function is to record and analyze signals from processes in which physical variables, such as force, pressure or torque, vary as a function of displacement, angle or time according to a defined curve. The resultant measurement curve is analyzed using graphical evaluation elements such as windows, envelopes and thresholds. The result of the analysis is classified as "OK" or "NOT OK" (NOK) and can...

Open the catalog to page 13

Operating Manual DIGIFORCE® model 9307 - 14

Ambient conditions The following requirements must be met when storing the DIGIFORCE 9307: ® • The DIGIFORCE 9307 must be packed in clean packaging • Store in dry environment • No condensation • Store at temperatures between 0° C and +60° C The following requirements must be met when operating the DIGIFORCE 9307: • Always operate indoors • Maximum height: above sea level 2000 m • Operate at temperatures between: +5 °C ... +40 °C, ideally +23 °C • Humidity: 80% up to +31 °C, decreasing flinearly above that temperature to 50% at Tmax, no condensation • Class of protecion:1 • Transient...

Open the catalog to page 14

Operating Manual DIGIFORCE® model 9307 - 15

DANGER Electrical shock hazard ® Disconnect the DIGIFORCE 9307 from the power plug before cleaning. ® Disconnect the DIGIFORCE 9307 from the power plug and use a slightly damp cloth for cleaning the unit. Do not immerse the DIGIFORCE 9307 in water or hold it under running water. Do not ® use strong cleaning agents as these may damage the DIGIFORCE 9307. Use a ® slightly damp cloth to clean the DIGIFORCE 9307. Personnel must be familiar with the relevant regulations. They must follow these regulations. Only trained personnel who are familiar with the applicable safety regulations are...

Open the catalog to page 15

Operating Manual DIGIFORCE® model 9307 - 16

DANGER Electrical shock hazard ® Never switch on the DIGIFORCE 9307 if it shows signs of damage incurred in ® transit. Only ever use the DIGIFORCE 9307 under the conditions specified in this operating manual. ® Inspect the DIGIFORCE 9307 for damage. If you suspect that the unit has been damaged during shipping, notify the delivery company within 72 hours. ® The DIGIFORCE 9307 should be shipped only in its original packaging or in packaging capable of providing an equivalent degree of protection. burster praezisionsmesstechnik gmbh & co kg provides a manufacturer's warranty for a period of...

Open the catalog to page 16

Operating Manual DIGIFORCE® model 9307 - 17

2.10 Error messages when the unit is powered up ® During boot-up, the DIGIFORCE 9307 may display certain error messages. ® The following errors mean that the DIGIFORCE 9307 must be sent in for checking and possibly repair: German error message English error message "Nichtflüchtige Daten korrupt" "Non-volatile data error" "Abgleich Fehler" "Calibration error" "EEPROM von Analogplatine ist leer“ "EEPROM of analog board is empty" "Fehler beim Lesen der MAC Adresse" "MAC Address Reading Error" In any of these cases, please call our Service department on +49-7224-645-53 or email:...

Open the catalog to page 17

Operating Manual DIGIFORCE® model 9307 - 18

Principles of design and operation ® Please refer to the DIGIFORCE 9307 data sheet for technical data, full details of dimensions, weight, degree of protection etc. The DIGIFORCE 9307 monitors processes in which precisely defined functional relationships between two or more measured quantities need to be demonstrated. These measured quantities are recorded synchronously during the manufacturing process or subsequent functional testing to produce a measurement curve, which is then assessed using graphical and mathematical evaluation techniques. After internal evaluation, the measurement...

Open the catalog to page 18