2316 EN ■ Measuring ranges from 2 mQ to 200 kQ ■ Temperature compensation for all materials ■ Input voltage protection up to 400 Vrms ■ Ethernet-, USB-, RS232 - as well as PLC interface Application Fast and accurate measurements of the smallest resistance values are possible with the milliohmmeter RESISTOMAT® model 2316. Due to the rugged aluminium injection moulding desktop housing with membrane keypad it is suitable for use in laboratory and industrial environment likewise. Wires and coils can be measured with temperature compensation. The temperature of the sample is measured with a Pt 100 or pyrometer and the resistance is then corrected to the equivalent at e.g. 20 °C (adjustable) in the instrument. The application range is very wide such as the measurement of: ► Transformer motor coil windings ► Cables and wires on the drum or as meter samples ► Switch and relay contacts ► Connections and transitions at power rails and many more For a cooling curve recording with freely selectable time interval a data logger for up to 1000 values is available. The complete control via the various interfaces enables the setup of fully automatic test stations. The instrument features a PLC interface for integration into production process control classification and makes selection of the samples an easy task. Technical changes reserved. All data sheets at www.burster.com Description The device works according to the proven 4-wire measurement method which eliminates errors caused by test lead and contact resistances. Thermo voltages that might be in the measurement circle would be compensated automatically by this measurement method. The control of the measurement leads is done with an integrated cable fraction detection. A temperature compensation for any given sample material such as copper, aluminium, tungsten, etc. is self-evident. The temperature measurement is done by an external Pt 100 sensor or by an external infrared measurement device (ref. to accessories). A special measurement voltage input protection was developed for testing large inductive samples so that voltage peaks do not cause permanent damage while pinching off the sample. 16 device settings such as the measurement range, limit values, temperature coefficient, etc. can be saved in order to test samples with different parameters in an automatic measurement system. All device specific settings are shown to the user via display. Calling up the settings is done via keypad or via PLC interface with a bit pattern (4-bits). It goes without saying that all device settings may also be effected via the available interfaces. The high-contrast LCD display with backlight assures very good reading of the measurement value in dark as well as bright spaces. burster praezisionsmesstechnik gmbh & co kg Germany www.burster.com Talstr 1-5 • Gernsbach 76593 • Phone +49-7224-6450 info@burst

Measurement Display test object resistive inductive temperature coefficient measuring mode temperature device program upper limit evaluation result <=> lower limit status/error display Measurement Program Measuring program Measuring range Limit values Temperature coefficient Measuring mode For fast object changes, RESISTOMAT® 2316 can store up to 16 measurement programs, which can be executed either by PLC, by hand or RS232 (USB, Ethernet) Reference temperature Reference length Rear Side measurement input either via 5-pin bayonet socket or 4 x laboratory safety sockets (4 mm ø) Ethernet interface...

Device and Documentation Software Following features are available: ► Full control of RESISTOMAT® model 2316 ► Online display of the measuring values including limits in graphic or tabular mode ► Direct storage of the measuring values with time stamp in ASCII files ► Export of all data in ASCII format to MS-EXCEL ► Printout of a test certificate with your own logo ► Complete cooling curve record and printout of motor System requirements: Processor: Pentium 500 MHz (at least) Graphic: VAG 800 x 600 (at least) 256 colours (at least) Memory: 128 MB RAM (at least) (WIN7, WIN8, WIN10) Hard Disk: approx....

Technical Data Construction The device has a service-friendly construction in a sturdy aluminium die casting housing which enables good access to the various components. The operation is done via the membrane keypad. The connections for the sample, the in- and outputs of the interfaces as well as the Pt100-sensors are located at the backside of the device. The device features a diagnosis function for current source, amplifier, display, internal operation voltage and PLC I/O. Connections Measuring input: Ethernet: Calibrations Sets: 1 *RESISTOMAT® model 2316-V0001 only "adjustable at the device...