Delivery: ex stock | Warranty: 24 months Ultra-Miniature Load Cell MODEL 8416 Highlights easuring ranges from 0 ... 20 N up to 0 ... 5 kN M 0 ... 4.5 lbs up to 0 ... 1124.0 lbs Dragchain cable Inexpensive Minimum diameter Options burster TEDS Temperature compensated range -40 °C ... +90 °C Standardization of the nominal sensitivity Connection cable from single strand Applications Equipment construction Production lines Measuring and control equipment Testing systems Handling gear Model 8416 original size Due to their extremely compact design, these load cells can be used wherever static or dynamic load forces have to be measured in very tight spaces. Model 8416 is perfect for use in micro-technology and just as suitable for measuring tasks in the research and development sector. The ultra-miniature compression load cell model 8416 is a flat, circular disc, the bottom of which is sealed with a cover. The load application button for receiving the compression forces is an integrated part of the sensor. The sensor element inside the body carries a strain gage full bridge which outputs voltage directly proportional to the measurement variable upon application of force. The short nominal measurement distance of the ultra-miniature compression load cells due to their design provides a high degree of rigidity. If needed, the nominal characteristic value can be standardized in the sensor connection cable. This allows for quick and easy interchange or simultaneous connection of several sensors to a single evaluation unit. burster Sensors and Process Instruments – Technical changes reserved. All data sheets at www.burster

Characteristic curve deviation* Relative hysteresis Measuring range calibrated in N and kN from 0 ... Accuracy Relative non-linearity* Temperature effect on zero output Temperature effect on nominal sensitivity Electrical value Sensitivity nominal Measurement direction compression direction option 0.8 mV/V (±0.5 %) realized on board in connection cable, 1.7 m from sensor housing or 0.3 m from cable end Bridge resistance 350 Ω nominal (deviations are possible) Insulation resistance Environmental conditions Nominal temperature range Operating temperature range Mechanical values Deflection full...

Dimensional drawing Model 8416 Measuring range from 0 ... Option Standardization, TEDS Cable extension General tolerance of dimension Mounting The measurement force must be introduced centrically and without any lateral forces. To prevent contact at just a few points, ensure that the sensor is installed on a flat surface. Mounting instructions The sensor can be secured, for example, with silicon, wax or adhesive cement. Do not subject the sensor to lateral clamping forces as these would lead to measurement errors. When handling and installing the sensor, ensure that the cable outlet and sensor...

Electrical termination Output signal burster load cells are based on a strain-gage Wheatstone bridge. This measurement principle means that the output voltage mV/V is highly dependent on the sensor supply voltage. Our website contains details of suitable instrumentation amplifiers, indicator and display devices and process instruments. Excitation + (white) Output signal - (green) Excitation - (brown) Output signal + (yellow) Sensor - (grey)* TEDS I/O (red)** TEDS GND (blue)** Shield * only for extended cables of length 5 m or more ** option 8416 Measuring range from 0 ... Electrical termination...

Calibration Test and calibration certificate Included in scope of delivery of sensor Amongst other data, includes figures for zero point, full-scale output and calibration offset Standard factory calibration certificate for load cells or measurement chains (WKS) Optionally available Our standard factory calibration certificate includes 11 measurement points, starting at zero, spread evenly in 20% steps over the full measuring range, for increasing and decreasing load under the same installation conditions. Special factory calibration certificate for load cells or measurement chains (WKS) On request...

Order Code Measuring range 0 ... Delivery ex stock at short notice N 8 Nominal sensitivity/not standardized Connection cable 1.7 m (with standardization in the cable 2 m) Connection cable 3 m, extended by a circuit board at 1,7 m * Connection cable 5 m extended * * shortened delivery time compared with cable length 3 m and 5 m in one piece Open cable ends + 6 cm single strands 9 pins Sub-D connector model 9900-V209 9 pins Sub-D connector model 9900-V209 for 9163-V3xxxx 12 pins round connector model 9941 for burster desktop devices 9 pins Sub-D connector with burster TEDS model 9900-V229 Non-linearity...