Delivery: ex stock | Warranty: 24 months High Precision Compression Load Cell MODEL 8527 Highlights Measuring ranges from 0 ... 500 N to 0 ... 100 kN Non-linearity 0.035 % F.S. Highest manufacturing quality Also suitable for dynamic measurements Options KS (Factory Calibration Certificate) or W DAkkS (German Accreditation Body) calibration burster TEDS Applications Reference measurements Calibration facilities Test benches All areas of mechanical engineering Product description High range The model 8527 high-precision compression load cell is the ideal load cell for reference measurement chains where highly precise measurement results are required. Its very high production quality and extremely low non-linearity of just 0.035 % F.S. make it a dependable choice for comparative measurements and calibration tasks Designed for a dynamic stress of up to 100 % of the full scale value, the model 8527 load cell is also suitable for situations where a rapid signal change with high amplitude occurs and has to be measured. The model 8527 high-precision compression load cell has a domed load button on top, onto which the compressive load being measured is applied. Inside the load cell is an elastic membrane, on which strain gages generate a resistance change in the measuring bridge and an output signal proportional to the load. For the best possible measurement results, the force should be applied axially and centrically to the load button. The mounting surface should ideally be hardened (60 HRC) and should not bend under the applied load. burster Sensors and Process Instruments – Technical changes reserved. All data sheets at www.burster.com

Measuring range calibrated in N and kN from 0 ... Accuracy Relative non-linearity* Characteristic curve deviation* Relative hysteresis Temperature effect on zero output Temperature effect on nominal sensitivity Electrical values Sensitivity nominal Measurement direction Compression direction Bridge resistance Insulation resistance Environmental conditions Nominal temperature range Operating temperature range Mechanical values Deflection full scale Maximum operating force Overload burst Dynamic performance recommended: 70 %; maximum: 100 % (of capacity) Installation Intended mounting screws Tightening...

Dimensional drawing 1 – Measuring ranges from 0 ... 0.5 kN up to 0 ... 20 kN | from 0 ... 112.4 lbs up to 0 ... 4.5 klbs Measuring range from 0 ... Option Standardization, TEDS Cable extension burster Sensors and Process Instruments – Technical changes reserved. All data sheets at www.

Dimensional drawing 1 – Measuring ranges from 0 ... 50 kN up to 0 ... 100 kN | from 0 ... 11.1 klbs up to 0 ... 22.4 klbs Measuring range from 0 ... Option Standardization, TEDS Cable extension burster Sensors and Process Instruments – Technical changes reserved. All data sheets at www.

Electrical termination Output signal burster load cells are based on a strain-gage Wheatstone bridge. This measurement principle means that the output voltage mV/V is highly dependent on the sensor supply voltage. Our website contains details of suitable instrumentation amplifiers, indicator and display devices and process instruments. Excitation + (white) Output signal - (green) Excitation - (brown) Output signal + (yellow) Sensor - (grey) TEDS I/O (red)** TEDS GND (blue)** Shield 8527 Measuring range from 0 ... Electrical termination Specifications highly flexible, shielded, drag chains suitable....

Calibration Test and calibration certificate Included in scope of delivery of sensor Amongst other data, includes figures for zero point, full-scale output and calibration offset Standard factory calibration certificate for load cells or measurement chains (WKS) Optionally available Our standard factory calibration certificate includes 11 measurement points, starting at zero, spread evenly in 20% steps over the full measuring range, for increasing and decreasing load under the same installation conditions. Special factory calibration certificate for load cells or measurement chains (WKS) On request...

Order Code Measuring range 0 ... Delivery ex stock at short notice N 8 Nominal sensitivity/not standardized Connection cable 1.7 m (Standardization 2 m) Connection cable 3 m extended * Connection cable 5 m extended * (with sens line) * shortened delivery time compared with cable length 3 m and 5 m in one piecek Open cable ends + 6 cm single wires 9 pins Sub-D connector model 9900-V209 9 pins Sub-D connector model 9900-V209 for 9163-V3xxxx 12 pins round connector model 9941 for burster desktop devices 9 pins Sub-D connector with burster TEDS model 9900-V229 8 pins coupling connector model 9900-V245...