Delivery: ex stock | Warranty: 24 months Tension and Compression Load Cell MODEL 8523 Highlights easuring ranges from 0 ... 20 N to 0 ... 5 kN, M 0 ... 4.4 lbs up to 0 ... 1.1 klbs Tilt-free installation thanks to point-contact mounts Excellent price/performance ratio Easy mounting Options Pull plate for directing tension forces Load buttons for simple measurement of compressive loads Standardized output signal burster TEDS Applications Machine tools Reference sensor for comparative measurements All forms of test benches R&D Product description High ranges With load buttons The tension & compression load cells from the 8523 series are designed for a wide range of uses. The sensors feature many benefits, including three point-contact mounts for tilt-free installation. Thanks to this feature, excellent measurement results can be achieved even with a sub-optimum mounting surface. The force to be measured is applied to the central threaded hole in the tension or compression direction. For measuring purely compressive loads, using load buttons from our accessories range saves the need for complex sensor-integration mechanisms. Tensile loads in rods or chains can also be detected with ease using the optional pull plate. Inside the sensor is an elastic membrane, on which are applied strain gages connected in a full Wheatstone bridge. If a tensile or compressive load is applied to the sensor, the ohmic resistance of the measuring bridge changes and detunes the output signal in proportion to the measured load in mV/V. With pull plates + rod end bearings burster Sensors and Process Instruments – Technical changes reserved. All data sheets at www.burster.com

Measuring range calibrated in N and kN from 0 ... Characteristic curve deviation* Relative hysteresis Relative non-linearity* Temperature effect on zero output Temperature effect on nominal sensitivity Electrical values Sensitivity nominal tension and compression direction. Load calibration in compression direction. The full-scale output is likely to be different when used in the tension direction. Positive output signal in compression direction. Measurement direction option (from measuring range of 100 N) 1.5 mV/V (±0.5 %) Standardization** Bridge resistance 350 Ω nominal (deviations are possible)...

Dimensional drawing 1 – Measuring ranges from ≤ 0 ... ±500 N | from ≤ 0 ... ±112.4 lbs Measuring range from 0 ... Option Standardization, TEDS L/B/D 90/8/7 Cable extension Central blind threaded hole T Number of clearing holes in Ø Dimensional drawings M8 x 1.25 3 (with edges, H + 0.9 mm) dimensional drawing 1 burster Sensors and Process Instruments – Technical changes reserved. All data sheet

Dimensional drawing 2 – Measuring ranges from ≥ 0 ... ±1000 N | from ≥ 0 ... ±224.8 lbs Measuring range from 0 ... Option Standardization, TEDS L/B/D 90/8/7 Cable extension Central blind threaded hole T Number of clearing holes in Ø Dimensional drawings M8 x 1.25 3 (with edges, H + 1.3 mm) dimensional drawing 2 Electrical termination Output signal burster load cells are based on a strain-gage Wheatstone bridge. This measurement principle means that the output voltage mV/V is highly dependent on the sensor supply voltage. Our website contains details of suitable instrumentation amplifiers, indicator...

Measuring range from 0 ... Electrical termination highly flexible, shielded, drag chains suitable. Bending radius three times the diameter for fixed cable, ten times the diameter for cable permanently moving Specifications Cable fastening Bending protection cable cover cable connection with tension relief shrinking tube rubber cover Bending radius three times the diameter for fixed cable, ten times the diameter for cable permanently moving. Bending radius Cable type Options Pull plates Sensor with pull plate A pull plate extends the range of potential uses of tension & compression load cells...

Accessories Rod end bearings The 8523 load cell can be optionally supplied with a rod end bearing. In combination with a pull plate (see option), up to two rod end bearings can be used. Rod end bearings ensure optimum load application when the sensor is used in the tension direction. In addition, they can compensate for slight misalignment in the compression direction. Rod end bearings with external thread Optimal force introduction Compensation of misalignments Very high dynamic und static load capacity Material: stainless steel Temperature range: - 45 °C to + 120 °C PTFE insert, maintenance-free...

Compatible for measuring range from 0 ... Installation Tightening torques Other Mass Connectors and units Order Code Connectors 9941 Connectors 12 pin, suitable to all burster desktop units Connectors 9 pin, suitable to SENSORMASTER, DIGIFORCE® and TRANS CAL Connectors 9 pin with TEDS Connectors 8 pin, suitable to ForceMaster Mobile measuring device with strain gage simulator and sensor test (Ri, Ra, Shunt, RISO) Sensor electronics, amplifier and process control units like digital indicator model 9180, model 9163, modular amplifier model 9250 or DIGIFORCE® model 9307 Calibration Test and calibration...

Order Code Measuring range For short delivery ex stock N 8 Nominal sensitivity/not standardized * for measuring range from 100 N ... 5 kN, temperature range limited to 0 ... +60 °C Connection cable 1.7 m (with standardization in the cable 2 m) Connection cable 3 m extended * Connection cable 5 m extended * (with sens line) * shortened delivery time compared with cable length 3 m and 5 m in one piece Open cable ends + 6 cm single wires 9 pins Sub-D connector model 9900-V209 9 pins Sub-D connector model 9900-V209 for 9163-V3xxxx 12 pins round connector model 9941 for burster desktop devices 9 pins...