Catalogs >
burster präzisionsmesstechnik gmbh & co kg >
Data Sheet Model 8523

Data Sheet Model 8523
8Pages

Catalog excerpts

Delivery: ex stock | Warranty: 24 months Tension and Compression Load Cell MODEL 8523 Highlights M easuring ranges from 0 ... 20 N to 0 ... 5 kN, 0 ... 4.4 lbs up to 0 ... 1.1 klbs T ilt-free installation thanks to point-contact mounts E xcellent price/performance ratio E asy mounting Options Pull plate for directing tension forces L oad buttons for simple measurement of compressive loads Standardized output signal burster TEDS Applications M achine tools Reference sensor for comparative measurements A ll forms of test benches R &D Product description High ranges With load buttons The tension & compression load cells from the 8523 series are designed for a wide range of uses. The sensors feature many benefits, including three point-contact mounts for tilt-free installation. Thanks to this feature, excellent measurement results can be achieved even with a sub-optimum mounting surface. The force to be measured is applied to the central threaded hole in the tension or compression direction. For measuring purely compressive loads, using load buttons from our accessories range saves the need for complex sensor-integration mechanisms. Tensile loads in rods or chains can also be detected with ease using the optional pull plate. Inside the sensor is an elastic membrane, on which are applied strain gages connected in a full Wheatstone bridge. If a tensile or compressive load is applied to the sensor, the ohmic resistance of the measuring bridge changes and detunes the output signal in proportion to the measured load in mV/V. With pull plates + rod end bearings burster Sensors and Process Instruments – Technical changes reserved. All data sheets at www.burster.com

Open the catalog to page 1

Relative non-linearity* Characteristic curve deviation* Relative hysteresis Temperature effect on zero output Temperature effect on nominal sensitivity Electrical values Sensitivity nominal Measurement direction Standardization** Bridge resistance Excitation Insulation resistance tension and compression direction. Load calibration in compression direction. The full-scale output is likely to be different when used in the tension direction. Positive output signal in compression direction. option (from measuring range of 100 N) 1.5 mV/V (±0.5 %) 350 Q nominal (deviations are possible)...

Open the catalog to page 2

burster Sensors and Process Instruments - Technical changes reserved. All data sheets at www.burster.com

Open the catalog to page 3

Option Standardization, TEDS L/B/D 90/8/7 Cable extension Electrical termination Output signal burster load cells are based on a strain-gage Wheatstone bridge. This measurement principle means that the output voltage mV/V is highly dependent on the sensor supply voltage. Our website contains details of suitable instrumentation amplifiers, indicator and display devices and process instruments. Sensor + (pink)* Excitation + (white) Output signal - (green) Excitation - (brown) Output signal + (yellow) Sensor - (grey)* TEDS I/O (red)** TEDS GND (blue)** * only for extended cables of length 5 m...

Open the catalog to page 4

Electrical termination Specifications Cable fastening Bending protection Bending radius Cable type highly flexible, shielded, drag chains suitable. Bending radius three times the diameter for fixed cable, ten times the diameter for cable permanently moving cable cover shrinking tube cable connection with tension relief rubber cover Bending radius three times the diameter for fixed cable, ten times the diameter for cable permanently moving. Options Pull plates A pull plate extends the range of potential uses of tension & compression load cells to measuring tensile loads in moving assemblies...

Open the catalog to page 5

Rod end bearings The 8523 load cell can be optionally supplied with a rod end bearing. In combination with a pull plate (see option), up to two rod end bearings can be used. Rod end bearings ensure optimum load application when the sensor is used in the tension direction. In addition, they can compensate for slight misalignment in the compression direction. Optimal force introduction Compensation of misalignments Very high dynamic und static load capacity Material: stainless steel Temperature range: - 45 °C to + 120 °C PTFE insert, maintenance-free DIN 648 series K Bore holes H7,...

Open the catalog to page 6

Order Code burster Sensors and Process Instruments - Technical changes reserved. All data sheets at www.burster.com

Open the catalog to page 7

Nominal sensitivity/not standardized ‘ for measuring range from 100 N ... 5 kN, temperature range limited to 0 ... +60 °C Connection cable 1.7 m (with standardization in the cable 2 m) Connection cable 3 m Connection cable 5 m Connection cable 3 m extended * Connection cable 5 m extended * (with sens line Brochure Our brochure „Load cells for production, automation, R&D and quality assurance" is available for download on our website. It conatains numerous applications, detailed product specifications and overviews. Product videos Watch our How-to-do video at: www.youtube.com/bursterVideo...

Open the catalog to page 8

Data Sheet Model 8523 8Pages

Catalog excerpts

All Burster präzisionsmesstechnik gmbh & co kg catalogs and technical brochures

Data Sheet Model 8523
8Pages