DATA SHEET Pneumatically operated 2 way angle seat control valve ELEMENT • Excellent combination of good control characteristic and high flow rate • Long service life • Control units can be mounted directly without external tubing • Stainless steel housing with thread, clamp and weld end connection Product variants described in the data sheet may differ from the product presentation and description. Can be combined with Type 8696  Digital electropneumatic positioner for the integrated mounting on process control valves Type 8693  Digital electropneumatic process controller for the integrated mounting on process control valves Type 8692  Digital electropneumatic Positioner for the integrated mounting on process control valves Type 8694  Digital electropneumatic positioner for the integrated mounting on process control valves Type 8792  Digital electropneumatic Positioner SideControl Type description In line with Bürkert’s philosophy for modular valves and sensors the construction of Type 2300 angle-seat valve fulfils tough criteria for process environments. Unrivalled cycle life and sealing integrity is guaranteed by the proven self adjusting packing gland. The parabolic trim results in a flow characteristic approximately 35 % larger than conventional control valves. It is available in either stainless steel on stainless steel or with a durable PTFE seal for tight shut-off. The design enables the easy integration of automation modules whether they are digital electropneumatic positioner or process controller. The fully integrated system has a compact and smooth design, integrated pneumatic lines, IP65/67, NEMA Type 4X protection class and superior chemical resistance. This system has been engineered for reliable accurate control in applications where high flow rate is an advantage. Type 8793  Digital electropneumatic Process Controller SideControl Type 8791  Digital electropneumatic Positioner SideControl 1000475061 | Standard | EU | en | 202103 | 01 © Christian Bürkert GmbH & Co. KG, Subject to alteration

Table of contents 1. General technical data 8. Networking and combination with other Bürkert products Visit product website 

1. General technical data Product properties Dimensions Material Design Nominal diameter Safety setting in case of power failure Flow direction Performance data Operating pressure Nominal pressure Pilot pressure Seat leakage Leakage class III and IV Leakage class VI Kv value Operating characteristic Medium data Medium Detailed information can be found in chapter “5. Dimensions” on page 6. Detailed information can be found in chapter “4. Materials” on page 5. Angle seat control valve DN10…DN65, NPS ⅜…NPS 2½ Normally closed (control function A), normally open (control function B) Flow to open (below...

2. Circuit functions Control function (CF) Description Flow direction below seat for fluids, steam and gases CF: A, pneumatically operated control valve 2 (P) 2/2 way Flow direction below seat 1 (A) Normally closed by spring force CF: B, pneumatically operated control valve 2/2 way Flow direction below seat Normally open by spring force Description Food produce contact Materials in contact with the medium conform to EC regulation 1935/2004 (option) Materials in contact with the medium conform to FDA (option) Drinking water Suitable for use with drinking water for Medium temperature up to 85 °C...

4. Materials 4.1. Chemical Resistance Chart – Bürkert resistApp Bürkert resistApp – Chemical Resistance Chart You want to ensure the reliability and durability of the materials in your individual pplication case? Verify your combination of media and materials on our website or in a our resistApp. Start Chemical Resistance Check Element Pilot air ports Actuator Cover Piston seal Spring Pipe Spindle sealing Spindle Spindle guide Body seal Control cone Spring straight pin Seat seal Valve body Material Push-in connector PP (Standard) PPS Stainless steel 1.4561 (316Ti) FKM Stainless steel 1.4310 Stainless...

Nominal diameter (pipe) DN NPS 10 ⅜ 15 Actuator size 1.) Dimensions for B and H are maximum dimensions and can be up to 6 mm smaller, depending on nominal diameter and standard. Visit product website 

5.2. Valve system Continuous ELEMENT Note: • Dimensions in mm, unless otherwise stated • Please note actuator size A in table “5.1. Actuator” on page 6 With positioner TopControl Basic Type 8694   With positioner TopControl Type 8692   or with process controller TopControl Type 8693   With positioner TopControl Type 8696   Nominal diameter (pipe) DN NPS 10 ⅜ ½ 1.) Dimensions for B and H are maximum dimensions and can be up to 6 mm smaller, depending on nominal diameter and st

With remote positioner SideControl Type 8792   or with remote process controller SideControl Type 8793   Nominal diameter (pipe) DN NPS 10 ⅜ 15 ½ 20 ¾ 25 1 32 Actuator size 1.) Dimensions for B and H are maximum dimensions and can be up to 6 mm smaller, depending on nominal diameter and standard. Visit product webs

5.3. Body with threaded connection Note: Dimensions in mm, unless otherwise stated Visit product website  

5.4. Body with welded connection Note: Dimensions in mm, unless otherwise stated Nominal diameter (pipe) [NPS] ½ ¾ 1 1½ 2 2½ Visit product website  

5.5. Body with clamp connection Note: Dimensions in mm, unless otherwise stated Nominal diameter (pipe) Nominal diameter (pipe) Visit product website  

6. Performance specifications 6.1. Fluidic data Flow characteristics Note: • Modified equal percentage flow characteristic • Higher flow values compared to globe control valves Kv /K vs [%] 100 90 80 70 60 50 40 30 20 10 0 0 10 20 30 40 50 60 70 80 90 100 Stroke[%] Flow rate of standard control valve Overview of fluidic data for flow below seat Note: • KV value [m3/h]: Measured with water acc. to DIN EN 60534 - 2 - 4 • See “6.2. Operating limits” on page 14 Nominal diameter (pipe) Operating pressure max. SF: A (Seat leakage class) Seat seal Stainless steel [bar(g)] 16 (IV) 25 (IV) 25 (IV) 25...