Catalog excerpts
Oil / Water Cooler Series BWT § High exchange efficiency § Equally distributed turbulent flow § Maintenance free § Little installation space required § Broad temperature range § High fatigue life § Easy installation Bühler Technologies GmbH D - 40880 Ratingen, Harkortstr. 29 Tel.: + 49 (0) 2102 / 49 89-0 Fax: + 49 (0) 2102 / 49 89-20 Internet: www.buehler-technologies.com e-mail: fluidcontrol@buehler-technologies.com
Open the catalog to page 1
Why Coolers? There are basically two main concepts in the development of fluid power systems. One is to design systems minus a cooler and if the operational conditions show in practice that the system needs a cooler to install it later. This however requires compromises that usually result in financial overspend. The other concept recognises that a system originally designed with an integrated cooler can be built more compact, needs less installation space and runs more reliable due to the stabilized temperature of the fluid. Why Bühler? Since water is becoming a precious resource,...
Open the catalog to page 2
Cooling performance of different BWT types Cooling perfomance in kW 600 Oil flow rate in l/min The diagram shows the range of performance of the different basic types. For a more precise calculation we can provide a software which is available upon request. General Data BWT plate coolers are approved by the following authorities: Sweden Norway Canada Germany USA Finland Switzerland EU Statens Anläggningsprovning (SA) Kjelkontrollen Canadian Standard Association (CSA) Technischer Überwachungsverein (TÜV) Underwriters Laboratories (UL) Teknillinen Tarkastuskeskus (TK) Schweizerischer Verein...
Open the catalog to page 3
Volumen Litre Mounting Brackets for BWT Part No. 34BB05 34BB08 34BB080 34BB15
Open the catalog to page 4
Mounting Brackets for BWT Part No. 34BB10 34BB25
Open the catalog to page 5
Mounting Brackets for BWT Part No. 34BB35 34BB45 We recommend using two brackets for the types B35-090 and B120-060 up to B120-120.
Open the catalog to page 6
* SAE flanges: nominal pressure 3000 psi
Open the catalog to page 7
Installation The BWT plate cooler should be located to allow free access from all sides and good visibility. There are no particular installation restrictions, however the unit should be easy to drain in case of open air installation to prevent freezing. Connection of oil and water circuits. The connections from cooler to the system should be stress and vibration free. The use of flexible hoses or compensators is highly recommended. Please comply with local safety requirements and avoid any risk to the environment from oil spills etc.
Open the catalog to page 8All Bühler Technologies catalogs and technical brochures
-
Gas cooler series TC-MINI6 Pages
-
sample gas probe GAS 222.102 Pages
-
Oil/air cooler BLK ATEX-3GD7 Pages
-
Off-line cooler BNK ATEX-2GD6 Pages
-
Off-line cooler BNK ATEX-3GD6 Pages
-
Circular pumps BFP7 Pages
-
Circular pumps BFP ATEX-2GD8 Pages
-
Buhler catalogue for Fluid Control434 Pages
-
Bühler Gas Analysis catalogue394 Pages
-
Safety Flow Meter S-SM2 Pages
-
Controllers2 Pages
-
Flow Meter SM-62 Pages
-
Panel Filter AGF - FA - 52 Pages
-
Panel Filter AGF - FE 42 Pages
-
Panel Filter AGF - FE2 Pages
-
Sample Gas Filter AGF - T 302 Pages
-
display and control unit2 Pages
-
VSA 24-DM / DH / DP2 Pages
-
Oil/air coolers BNK7 Pages
-
Capacity sensor VSA 24-SM2 Pages
-
Nivotemp 61-0 WW series2 Pages
-
Water alarm WW 6 series2 Pages
-
GAS 222.202 Pages
-
BNF off line filter6 Pages
-
NV 716 Pages
-
NT 67 XP3 Pages
-
NT 619 Pages
-
NT M4 Pages
-
SM series2 Pages
-
P 1.13 Pages
-
AHF2 Pages
-
BF 2-S2 Pages
-
AGF2 Pages
