For securing to beams without drilling or welding for: sprinkler systems, heating, ventilation and air-conditioning systems, acoustics systems, electrical, piping and sanitation fittings, engineering and steel structures. The raised marking serves as anti-twist protection when tightening the set screw and is protected by internationally registered design DM/0081575! * Please note the different packaging unit and the different material. » As far as possible, VdS, FM and UL approved » Full range for M6 - M16 threaded rods from stock » Inch thread on request » Distances between jaws from 18 - 45 mm » Please also note “Product benefits" information sheet SURFACE FINISH: 50 pcs in box or according to customer specification / TKC: 20 pcs in box Malleable cast iron body, general tolerances according to DIN EN ISO 8062-3 CT8 TKC: steel casting GS-60 Mounted with DIN 933 8.8 hex bolt, end with cup point (CP) acc. to EN ISO 4753 and DIN 439 lock nut Galvanised acc. to DIN EN ISO 4042, hot-dip galvanised acc. to DIN EN ISO 1461, or also coated with zinc flake (e.g. Geomet) All of the dimensions stated above are approximate and may deviate both upwards and downwards. BTS Befestigungselemente-Technik GmbH PostFach 1262 D-54439 Saarburg QUALITY THAT FASTENED

BEAM CLAMPS WITH ZINC FLAKE COATING Fig. shows models TKN8, TKN10 and TK12 with Geomet 500B coating. Zinc flake coatings are used in all areas of application for corrosion protection of fastening elements and all kinds of metal parts. DETAILS OF THIS SURFACE » High mechanical and chemical resistance with low coat thickness thanks to a combination of the barrier effect of flake structure, controlled cathodic protection of zinc and passivation of zinc and aluminium. » Meets specifications of automative industry worldwide: Salt spray test in accordance with DIN EN ISO 9227 NSS/ASTM B117 » No hydrogen...

BEAM CLAMPSSTAINLESS STEEL For securing to beams in the Following areas: sprinkler systems, heating, ventilation and air-conditioning systems, acoustics systems, electrical, piping and sanitation Fittings, engineering and steel structures. Safe working loads [N] Advantages compared to the previous version:» No washers needed » Easier Installation and improved handling » Higher safe working loads » Due to a longer lead of the thread rod, no premature bending » With DIN 933 M10x40 set screw with cup point (CP] and DIN 439 hex nut » Marking “9mm", “11mm" or ‘"13mm" and material MATERIAL: Stainless...

BEAM CLAMPS PRODUCT BENEFITS Product benefits of approved beam clamps: » » » » Enable use in certified fixed sprinkler systems Load values assured by independent approval bodies Set screw with cup point end to prevent sideways slipping off the I-Beam In case of beam clamps with plain hole a simple height adjustment can also be undertaken after assembling » Pre-assembly with threaded rod and lock nut possible Further product benefits of BTS beam clamps: » Malleable cast iron body, made in Germany » Prior to processing, inspection of all cast parts for visible bubbles » Set screws and lock nuts...

BEAM CLAMPS Pull direction against the screw Pull direction against the lower jaw Our type TK and TKN beam clamps can be fixed with the pull direction against the set screw or against the lower jaw. Please see our installation instructions for further information. All of the dimensions stated above are approximate and may deviate both upwards and downwards. BTS Befestigungselemente-Technik GmbH Postfach 1262 D-54439 Saarburg

According to VdS regulations the use of safety straps for beam clamps is compulsory for fixing pipes larger DN65. All beam clamps can be secured with a safety strap against sideways slipping from the beam. Responsible authority regulations are to be observed. MATERIAL: Steel SURFACE FINISH: Zinc-plated acc. to DIN EN ISO 4042 All of the dimensions stated above are approximate and may deviate both upwards and downwards. BTS Befestigungselemente-Technik GmbH PostFach 1262 D-54439 Saarburg QUALITY THAT FASTENED

Beam clamps with U-bolt » Completely pre-installed mounting kit with plate, hexagon nuts and washers » U-Bolt for centring the strut channel » The strut channel can be adjusted even after installing the beam clamps SCOPE OF DELIVERY: U-Bolt, base plate, 2 hexagon nuts, 2 washers SURFACE: Zinc plated acc. to DIN EN ISO 4042, hot dip galvanized All of the dimensions stated above are approximate and may deviate both upwards and downwards. Assembly instructions The Following safe working loads "F" apply for BTS beam clamps with U-Bolt and strut channels For static load. Beam clamps have to be used...