Catalog excerpts
Burst Alert® Sensors For immediate notification of a pressure relief event Visit our website for the most complete, up-to-date information
Open the catalog to page 1Burst Alert® Sensors for Rupture Disks and Other Devices Sensor Type BAS+TM Armored: ABAS+TM Features • Polyimide film • Tantalum conductor wire • Dual path conductor • Reconnect StopsTM • Wide conductor separation Burst Pressures See Table 1 Note: Two Reconnect StopsTM are seen at the breaking ends of the tantalum conductor wire run into the gasket. The stops provide electrical insulation to minimize risk of sensor reconnection after a pressure relief event. Use with the following rupture disk type Sure-Saf Order as EC-Alert Sensor: ECR, ECV, ECT, V/ECR (see table 1) Forward acting...
Open the catalog to page 2Burst Alert® Sensors Sensor Type Features • Polyimide film DASTM TM • Tantalum conductor wire DASS • Dual path conductor Armored: • Domed to accommodate TM ADAS disk dome TM ADASS Use with the following rupture disk type XT, XB, XN-85S and XN disks 4 inches (100mm) and larger used in NX-7R or NXV-7R safety heads. B, BV, Tension D, DV, XN-85 disks used in special reduced height loaded disks safety heads that do not enclose the disk dome. Atmospheric vent type disks: AV, AVV, AVE, AVEL Burst Pressures The response pressure capability of the DAS family of sensors matches the minimum burst...
Open the catalog to page 3Operation / Electrical Information Burst Alert Sensors operate in a “normally closed” electrical circuit with a polymer membrane supporting its electrical conducting circuit. When the pressure event (disk rupture / valve opening) occurs, the flow (gas or liquid) breaks the tantalum electrical conductor located on the polymer membrane. The electrical status of the sensor changes to “normally open.” The recommended maximum operating limits for Burst Alert Sensors is a current of 500mA, maximum voltage 24 VDC; satisfactory operation can be obtained at a few milliamperes current. Gaskets:...
Open the catalog to page 4All BS&B SAFETY SYSTEMS catalogs and technical brochures
-
GLP-S™ Reverse Buckling Disk
2 Pages
-
LO-TO-FLO™ Safety Head
2 Pages
-
VENT-SAF™ Explosion Panels
4 Pages
-
Buckling Pin Relief Technology
12 Pages
-
Burst Disk Monitors™ (BDM)
4 Pages
-
VIS-U-TEC™ Sensor
2 Pages
-
Type D
8 Pages
-
Tank Car Rupture Disks
2 Pages
-
Rupture Disk
12 Pages
-
Introduction to Rupture Disk
14 Pages
-
Corporate Profile
20 Pages
-
The VAC-SAF? System
12 Pages
-
SAF-T-GRAF? Graphite Disks
4 Pages
-
SURE-SAF? System
4 Pages
-
ECO-SAF? System
8 Pages
-
GCR-S? Reverse Buckling Disk
2 Pages
-
BIO-SAF? System
16 Pages
-
GCR-N? Reverse Buckling Disk
1 Pages
-
GLP-S? Reverse Buckling Disk
2 Pages
-
SmartSystem
4 Pages
-
MRB series
1 Pages
-
SIGMA, SIGMA EXL
4 Pages
-
VENT-SAF? Explosion Vents
8 Pages
-
EXPLOSION VENTING
4 Pages
-
AVB
2 Pages
-
Nu-Saf Plus
8 Pages
-
Type B
8 Pages
-
Conversion Factors
2 Pages
-
SR-TC Rupture Disk
2 Pages
-
Composite Bursting Disc Type D
12 Pages
-
SKR-U Reverse Buckling Disk
4 Pages
-
The STA-SAF System
12 Pages
-
Mono Block Graphite Disks
8 Pages