A5S0DD0 (non-hazardous area)
7Pages

Differential-Hall-Effect based Sensors for Detection of Speed in Non-Hazardous Areas Series A5S0DD0 / A5S0DS0 KEY FEATURES SIL3/IEC 61508:2010 certified by TÜV Detection of rotational speed in non-hazardous areas Speed range from 0 Hz to 25 kHz Air gap to the gear/pole wheel up to 2.5 mm (depending on the profile size) Temperature range -40…+125 °C (-40…+255 °F) Differential principle diminishes the influence of external magnetic stray fields and of machine vibration Sealed stainless steel enclosure > 200 bar pressure to the sensor tip Available for connection via tight plug, or with firmly attached Teflon® cable Powerful square wave output signal equally high over the entire speed range Sensor short circuit proof and protected versus polarity error A5S0 sensors – the best choice for demanding applications The BRAUN Speed Sensors Series A5S are TÜV certified for SIL3 acc. IEC 61508:2010 and therefore meet the high SIL3 standards. The correct choice of sensor is always a prerequisite to achieving a successful solution. Therefore BRAUN A5S0 sensors base on the proven Differential-Hall-Effect principle. Their low end of 0 Hz allows monitoring the machine down to zero speed. In addition, they are contact-free, wear-free, maintenance-free, and unsusceptible versus external magnetic stray fields and machine vibration. These characteristics make the series of A5S0 sensors especially suited for all applications where high accuracy and reliability are at a premium. In contrast, other sensors like magnet-inductive or static Hall sensors do not meet these demands. Each sensor in the series is available in various lengths and diameters and comes with a choice of connections. However, functionally all sensors have the same characteristics. The stainless steel sensor housing is sealed at the front and pressure-resistant (> 200 bars). A flat shaft is available or with a screw-in thread M12x1, M14x1, M14x1,5, M16x1, M16x1,5, M18x1, M18x1,5, M22x1, 5/8-18UNF-2A. Customized dimensions and thread specifications are possible. Accepting fine and coarse profiles, as gear wheels, slots, cams, holes in any ferrous material BENEFITS Contact-free with a large air gap, so the potential for damage is eliminated Wear-free due to its unique design principle Maintenance-free during lifetime, therefore minimized TCO Unsusceptible versus external magnetic stray fields and machine vibration Operates down to zero speed Can not be damaged by faulty wiring Almost every wheel profile can be used A5S0 Sensors do not influence each other, no mounting distance in between is required

Series A5S0DD0 / A5S0DS0 – the various Types and their Characteristics Sensors for Detection of Speed (one speed signal output) Non-Hazardous Areas (safe areas) Appropriate for any speed detection of rotating steel profile, unless the application has a unique requirement as listed below. Speed is signalized as the frequency of a pulse train. The Hall effect (named after its discoverer) utilizes a magnetic field that generates a voltage within a hall element. Its level is independent of its rate of change (i.e. the speed of motion) – unlike the induction effect of magnetic pick-up sensors,...

Sensor Series A5S0 Application Notes and Connection Types Application Notes BRAUN A5S0… speed sensors base on the proven Differential-Hall-Effect principle and are the best choice for demanding applications. Their low end of 0 Hz allows monitoring the machine down to zero speed. In addition, they are contactfree, wear-free, maintenance-free, and unsusceptible versus external magnetic stray fields and machine vibration. These characteristics make the series of A5S0… sensors especially suited to all applications where high accuracy and reliability are at a premium. Each series includes...

Figure includes special versions Sensor Positioning and Signal Features Sensor Positioning We recommend a radial orientation of the sensor to the wheel circumference. Its position in parallel to the rotational axis, though possible, may involve problems caused by a lateral shift of the wheel. All specifications refer to the recommended radial position. The differential principle of the A5S0… sensors, which diminishes the influence of other magnetic stray fields and machine vibrations, necessitates a correct positioning in reference to the profile of the wheel. Marking planes at the sensor...

Standard Design Versions length L Plug-in version shown with straight metal connector Plug-in version shown with angled metal connector Version with fixed Teflon® cable attached NPT-version with fixed Teflon® cable, only for 5/8"-18 (inch) thread See Ordering Key for available thread diameters D and length L A5S0DD0 / A5S0DS0

Specifications of A5S0DD0 / A5S0DS0 Conformity to Standards EU-Directive(s) Standard(s) 2014/30/EU (EMC Directive) EN 61326-1, EN IEC 61326-3-2 2014/35/EU (Low Voltage Directive) EN 61010-1 2011/65/EU (RoHS Directive) EN IEC 63000 Approved for UK according to the standards of the UK statutory requirements. SIL3 acc. IEC 61508:2010, EN ISO 13849:2008 Power Supply Supply voltage +5 V…+30 V DC Current approx. 20 mA + load current (may increase with longer distance transmission and high signal frequency up to > 60 mA). The sensor is protected versus polarity error. Signal Output Square wave...

Length of fixed Teflon® cable in m* Standard lengths for cable: x = 2, 5, 8, 10, 15, 20 *(omit for versions with screw-plug-in connection) Hazardous Area (Ex) 0 = Non-Ex version Signal Frequency b = DD : 0 Hz...25 kHz b = DS : 0 Hz...12 kHz Signal Output c = 0 : 1x Frequency c = 3 : 1x Frequency / 1x Direction* c = 4 : 2x Frequency, phase-shifted* *minimum nominal thread length 74 mm Unit of Shaft Diameter d = M : Metric d = N Inch and 1/2"-NPT at rear end of sensor (only in conjunc- : tion with thread 5/8"-18 (inch) and fixed Teflon® cable) d = U : Inch Thread of Shaft Diameter Standard...