Exhaust Gas Heat Exchanger product specs
12Pages

Exhaust Gas Heat Exchangers Scambiatori di calore per gas di scarico Abgaswärmetauscher

Exhaust Gas Heat Exchangers_ These heat exchangers are designed to remove thermal energy from the exhaust gas of natural gas, diesel and bio-fuel engines and transfer it to the water circuit. The extracted heat can be used for space heating, domestic hot water and any industrial process that requires hot water. • Standard range available for quick delivery. • Suitable for use with engines powered by conventional or alternative fuels. • Fully welded stainless steel construction for reliability and durability. • Can also be used to extract energy from gas or air and transfer it to a water...

Combined Heat Recovery The addition of Bowman exhaust gas heat exchangers enable waste heat recovery from the exhaust gas and can be used on Cogeneration/Combined Heat and Power (CHP) equipment. Typical configuration for CHP using Bowman Heat Exchangers HEADER TANK HEAT EXCHANGER SECONDARY WATER INLET SECONDARY WATER OUTLET EXHAUST GAS HEAT EXCHANGER Provision should be made for cooling the engine water, oil and gas when heat recovery is not required. Combined Heat Recovery Performance Table This table shows the heat that can be removed from each type of heat exchanger as shown in the...

Exhaust Gas Heat Exchanger Performance Table Typical examples of exhaust gas heat exchanger performance The figures below are a general guide only and are not based on any particular natural gas engine. They assume an air/fuel ratio of 10.23 : 1 by volume, a fuel consumption of 0.34m3/kWh (measured at 1.013 bar and 15ºC) and an exhaust gas temperature of 600ºC and a water inlet temperature of 80ºC. Typical Engine Power kW Exhaust gas flow kg/min Exhaust gas outlet temp °C Exhaust gas pressure drop kPa For larger sizes contact our sales department. Maximum Maximum Maximum Maximum working...

Installation and Operating Instructions Installation The heat exchanger must be installed horizontally and levelled accurately, with the primary circuit (tubeside) through the tubes and the secondary circuit (shellside) over the tubes. The heat exchanger should only be connected in “counter flow” with the secondary circuit (shellside) connections always being positioned on top. (See schematic diagram below). 8 Alternative installations may also be acceptable; consultation with our technical department for acceptance should be made prior to installation. It is very important that the...

Abgaswärmetauscher Diese Wärmetauscher sind für die Wärmerückgewinnung von Abgasen von Erdgas-, Diesel- und Biobrennstoffmotoren und für deren Übertragung auf den Wasserkreislauf ausgelegt. Die extrahierte Wärme kann zur Raumheizung, zur Erwärmung von Brauchwarmwasser und für alle industrielle Prozesse, die warmes Wasser benötigen, verwendet werden. Standardsortiment zur schnellen Lieferung verfügbar. Geeignet für Motoren bis 1 MW. Geeignet für Verwendung mit Motoren, die mit konventionellen und alternativen Brennstoffen angetrieben werden. Voll geschweißte Edelstahlkonstruktion zwecks...

Scambiatori di calore per gas di scarico Questi scambiatori di calore sono studiati per estrarre energia termica dai gas di scarico dei motori a metano, diesel e bio carburante e trasferirla al circuito ad acqua. Il calore estratto può essere utilizzato per il riscaldamento degli ambienti, dell’acqua calda residenziale e per qualsiasi processo industriale che richieda acqua calda. Gamma standard disponibile per spedizione immediata. Idonei per motori fino a 1 MW. Idonei per l’uso con motori alimentati da carburanti convenzionali e alternativi. Costruzione in acciaio inossidabile...

Spalinowe wymienniki ciepła Te wymienniki ciepła są zaprojektowane w taki sposób, że odprowadzają energię cieplną ze spalin wydalanych przez silniki zasilane gazem ziemnym, biopaliwem bądź silniki Diesla i przekazują ją do obwodu wodnego. Wydobyte ciepło może być wykorzystane do ogrzewania pomieszczeń, grzania wody do użytku domowego, a także w dowolnych procesach przemysłowych, które wymagają użycia gorącej wody. Zapewnia się szybką dostawę standardowego asortymentu. Odpowiednie do silników do 1 MW. Nadają się do stosowania z silnikami napędzanymi paliwami konwencjonalnymi oraz...