
Instructions for Installation and Operation Type FPM 0810, 0830, and 0850 Permanent Magnet DC Motor Controls (with driver board only, or with F-B-R board) Model 0810 up to 1/17 HP Model 0830 up to 1/6 HP Model 0850 up to 1/3 HP Input Voltage: . . . . . . . . . . . . . . . . . . . . 115 VAC±10%; 50/60 Hz, single phase Input Current: Model 0810 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.9 Amps AC Model 0830 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 Amps AC Model 0850 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.0 Amps AC Armature Voltage (nominal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-130 VDC Armature Current (max. continuous) Model 0810 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.50 Amps Model 0830 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.25 Amps Model 0850 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.30 Amps
Open the catalog to page 1BODINE LIMITED WARRANTY The Bodine Electric Company warrants all products it manufactures to be free of defects in workmanship and materials when applied in accordance with nameplate specifications. Bodine motors and gearmotors purchased with and used only with appropriately applied Bodine controls are covered by this warranty for a period of 24 months from the date of purchase or 30 months from date of manufacture, whichever comes first. Bodine motors and gearmotors used with non-Bodine controls and Bodine controls used with non-Bodine motors and gearmotors are covered by a 12 month warranty...
Open the catalog to page 2SAFETY PRECAUTIONS Connecting the Electronic F-E-R Board
Open the catalog to page 3CONGRATULATIONS!...and thank you for selecting a Bodine Type-FPM Adjustable Speed PM Motor Control. Vo or new control will provide the same excellent performance and reliability that have been characterise of Bodine products since 1905. We call i! ADE (After Delivery Economies). Bodine Electric Company takes pride in (he quality of ils products and in the ultimate satisfaction of ils customers. Every el fort is made to provide products free of defective design, workmanship, and materials, it will be considered a favor lo have cases of unsatisfactory service from Bodine prcducls brought to our...
Open the catalog to page 4For 220/240VAC single-phase operation, a 2:1 step-down isolation transformer may be used. Signal Transformer Type DU-1 (1 KVA) is recommended for models 0850 to 0858 and Type DU-1/2(.5 KVA) for models 0810 to 0838. The number of reversals are limited to 4 max. with model 0858 when using motor Type 42D7, unless brake resistor is mounted outside the enclosure. Standard Features Include: • Industrial quality enclosure (Encased Models 0815-8, 0835-8, 0855-8) • Terminal Block for easy electrical connections • L-Bracket/Heat Sink for simplified mounting • Inhibit Function standard on Models 0810,...
Open the catalog to page 5The following safety precautions must be observed during all phases of operation, service, and repair of this electronic drive/motor product . Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture and intended use of the products . Bodine Electric Company assumes no liability for the customer's failure to comply with safety requirements and practices . Warnings, such as the example below, highlight potentially dangerous procedures throughout this manual . Instructions contained in the warnings must be followed...
Open the catalog to page 6bility of the user, the manufacturer of the driven or driving equipment, and the manufacturer of the control or motor or generator.”* Bodine products are designed and manufactured to comply to applicable safety standards and in particular to those issued by ANSI (American National Standards Institute}, NEMA (National Electrical Manufacturers Association), U.L. (Underwriters Laboratories, Inc.}, and CSA (Canadian Standards Association}. * Standards Publication No. ANSI CS.1/NEMA MG-2. “Safety Standard for Construction and Guide for Selection, Installation and Use of Electric Motors and Generators.”...
Open the catalog to page 7ENVIRONMENT Sparking of brushes in commutated DC motors occurs during normal operation. In addition, open controls or controls in ventilated enclosures may emit flame during failure. Bodine’s totally enclosed standard PMDC gearmotors and motors are not explosion-proof, but Bodine offers several AC and BLDC explosion-proof gearmotors and motors for hazardous locations (e.g. environments where flammable gases or vapors might be present). Bodine recommends to only use approved explosion-proof products in hazardous locations. In addition, please note that moisture will increase the electrical shock...
Open the catalog to page 8REVIEWING YOUR CONTROL SELECTION Before proceeding with The installation, review (he application to confirm that Ihe proper motor and speed control have been selected. This should be done after reading this manual and all applicable safely standards. 11 in doubt, contact your Bod in e Representative, or the Home Office if there is no Representative in your area. Any selection or application suggestions made by Bodine Electric Company are o nly to ass i st t he oust o m er— a nd i n all case s, dete rmi n at io n of f it ne s s for purpose or use is solely the customer's responsibility. U n fess...
Open the catalog to page 9NOTE: Any exposed circuit boards should be handled in a static-protected area. The feature boards use CMOS circuitry. Static discharge into the feature boards must be avoided. All encased controls accept 1/2-inch liquid tight conduit fittings. For wire sizes and electrical connections refer to the National Electrical Code (NEC)– Article 430–”Motors, Motor Circuits, and Controllers” and/or applicable local area codes. If extension cords are used, they should be kept short for minimum voltage drop and optimum performance. Only copper wire with 60°C rated insulation is recommended. The terminal...
Open the catalog to page 1124 Pages
2 Pages
24 Pages
20 Pages
2 Pages
2 Pages
2 Pages
52 Pages
252 Pages
2 Pages
2 Pages
2 Pages
2 Pages
2 Pages
2 Pages
2 Pages
2 Pages
52 Pages