1. Catalogs
  2. BODINE ELECTRIC COMPANY
  3. Type ABL-3905 and ABL-3907

Type ABL-3905 and ABL-3907

Type ABL-3905 and ABL-3907
1 / 24 PagesView full catalog

Type ABL-3905 and ABL-3907

Product catalog summary
Specifications
The ABL-3905 and ABL-3907 are 24-Volt Brushless DC Motor Controls. Model 3905 supports up to 1/6 HP with a continuous output current of 2.5 to 10.0 Amps and a peak of 13.5 Amps. Model 3907 supports up to 3/8 HP with a continuous output current of 0 to 20.0 Amps and a peak of 30.0 Amps. Both operate with a power supply voltage of 24 to 35 VDC.
General Information
Bodine Electric Company focuses on quality and reliability. The manual provides essential installation and operation information for the ABL-3905 and ABL-3907 models, emphasizing quick and safe setup.
Control Description and Features
Designed for Bodine low-voltage brushless DC motors, these models offer quiet, maintenance-free operation. Speed control is possible via an external or on-board potentiometer or a 0 to 5 VDC analog input. Features include adjustable speed, torque, and acceleration/deceleration times, with a Smart Reverse™ circuit for safe direction changes.
Important Safety Precautions
Adherence to safety standards during installation and operation is crucial. Proper grounding, enclosure selection, and maintenance are emphasized. The controls are optimized for Bodine motors and should not be used with other brands without consultation.
Installation Instructions
Detailed steps are provided for mounting the control, making electrical connections, and configuring motor power and commutation sensor connections. Speed can be controlled using various methods, including external potentiometers and analog input voltage.
Operating Instructions
Preliminary checks are recommended before operation. Procedures for operating the control and making internal adjustments, such as maximum speed and acceleration settings, are outlined. Model 3907 includes torque/current limiting adjustments.
Troubleshooting and Warranty
A troubleshooting section addresses common issues. The warranty covers defects for 24 months when used with Bodine controls, or 12 months otherwise, requiring proof of purchase for claims.
Installation and Setup Procedures
1. Set the speed potentiometer to zero and open any ENA or Brake switches.
2. Connect AC power to the external power supply and turn it on if applicable.
3. Set the Direction switch for the desired motor rotation.
4. Close the ENA switch if used and adjust the speed potentiometer to start the motor.
5. If the motor does not operate, check connections and fuses, and refer to troubleshooting instructions if necessary.
Internal Adjustments
- Maximum Speed Trim Potentiometer: Adjusts motor speed from zero to 120% of rated speed.
- Acceleration Adjustment: Adjusts motor acceleration time from 0.35 to 8 seconds.
- Torque/Current Limiting Adjustment: Factory preset to 23 Amps peak, should not exceed 200% of motor's current rating.
Troubleshooting
Common issues include blown fuses, motor not starting, and unstable motor speed. Solutions involve checking power supply, adjusting potentiometers, and verifying connections.
Warranty Information
Bodine products are warranted to be free of defects for 24 months when used with Bodine controls, or 12 months otherwise. Warranty covers repair, replacement, or refund, excluding incidental expenses.
Additional Information
Bodine offers a wide selection of motors and gearmotors, with detailed specifications available on their website.
See more

Catalog excerpts

Type ABL-3905 and ABL-3907-1

Instructions for Installation and Operation Type ABL-3905 and ABL-3907 24-Volt Brushless DC Motor Controls Model 3905 up to 1/6 HP Model 3907 up to 3/8 HP SPECIFICATIONS Power Supply Voltage: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 to 35 VDC Output Current (Continuous): . . . . . . . . . . . . . . . . . . . . . . . . . . . Model 3905: 2.5 to 10.0 Amps Model 3907: 0 to 20.0 Amps Peak Current: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Model 3905: 13.5 Amps Model 3907: 30.0 Amps

 Open the catalog to page 1
Type ABL-3905 and ABL-3907-2

Read this manual completely and carefully. Pay special attention to all warnings, cautions, and safety rules. Failure to follow the instructions could produce safety hazards which could injure personnel or damage the control, motor, or other equipment. If you have any doubts about how to connect this control refer to the detailed sections of this manual and the specific control manual. QUICK REFERENCE ENLARGED VIEW OF CONTROL INPUTS (Page 12-15) Shielded Cable Unregulated Power Supply (24 to 35 VDC) (TAK and LMT output details on page 14 & 15) INTERNAL ADJUSTMENTS (Page 18) TORQ: Adjust motor...

 Open the catalog to page 2
Type ABL-3905 and ABL-3907-3

© 2024 Bodine Electric Company. All rights Reserved. All data subject to change without notice. Printed in U.S.A.

 Open the catalog to page 3
Type ABL-3905 and ABL-3907-4

GENERAL INFORMATION Thank you for selecting a Bodine Type ABL-3900 Series Low-Voltage Brushless DC Motor Control. Your new control will provide the same excellent performance and reliability that have been a Bodine tradition since 1905. Bodine Electric Company takes pride in the quality of its products and in satisfying its customers. Every effort has been made to provide you with a product free of defects in design, workmanship, and materials. In order for us to maintain our tradition of quality, please report any cases of unsatisfactory service or products to Bodine Electric Company promptly....

 Open the catalog to page 4
Type ABL-3905 and ABL-3907-5

Models 3905 and 3907 Low-Voltage Brushless DC Motor Controls are chassis type, designed to be mounted in a separate enclosure supplied by the user. They operate from a 24-Volt power supply or from a 24-Volt battery. The controls provide the necessary electronic commutation and phase current switching to operate Bodine low-voltage brushless DC motors. Their brushless design assures quiet, clean maintenance-free operation. Speed can be controlled by an external or on-board MAX speed trim potentiometer, or a 0 to 5 VDC analog input signal. Other features include adjustable maximum speed settings,...

 Open the catalog to page 5
Type ABL-3905 and ABL-3907-6

IMPORTANT SAFETY PRECAUTIONS The following safety precautions must be observed during all phases of installation, operation, service, and repair of this control. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture and intended use of the product. Bodine Electric Company assumes no liability for the customer’s failure to comply with safety requirements and practices. The use of electric motors and gearmotors, like that of all utilization of concentrated power, is potentially hazardous. The degree of hazard...

 Open the catalog to page 6
Type ABL-3905 and ABL-3907-7

Inspecting the Control Check the items you received against your purchase order. Carefully examine the control (and any optional kits or parts) for shipping damage. Report parts errors to Bodine. Shipping damage claims should be made to the freight carrier. Before installation, review the application to confirm that the proper motor and control have been selected. This should be done after reading this manual and all applicable safety standards. If in doubt, contact your Bodine representative, or the home office if there is no representative in your area. Although Bodine Electric Company assists...

 Open the catalog to page 7
Type ABL-3905 and ABL-3907-8

Ventilated Products Open, ventilated products are suitable for clean, dry locations where cooling air is not restricted. Do not insert anything into a product’s ventilation openings. Servicing Emergency field repairs must be made only by authorized Bodine service representatives. Repairs made by persons not authorized by the Bodine Electric Company will void the warranty. Field repairs must be limited to replacing the entire printed circuit board assembly. Because of the danger of introducing safety hazards, do not install substitute parts or perform any unauthorized modifications to electronic...

 Open the catalog to page 8
Type ABL-3905 and ABL-3907-9

INSTALLATION INSTRUCTIONS WARNING This control should only be installed by a qualified technician, electrician, or electrical maintenance person familiar with its operation and associated hazards. The National Electrical Code (NEC), local electrical and safety codes, and when applicable, the Occupational Safety and Health Act (OSHA) should be observed to reduce hazards to personnel and property. The user must provide a proper enclosure. Circuitry is not at ground potential. Do not perform work on or near the control while it is connected to the power supply. Exposed circuit boards should be protected...

 Open the catalog to page 9
Type ABL-3905 and ABL-3907-10

The power supply should be the last connection made in order to prevent accidental start-up. Disconnectthe power supply before making any other electrical connections. The following instructions are based on the assumption that a Bodine 24-Volt Brushless DC motor or gearmotor is being driven by the control. Chart 1 lists the Bodine motors and gearmotors that are designed to operate with the ABL-3905 and ABL-3907 controls. If there is any doubt about the control and motor combination you are using for your application or if you are planning to drive a non-Bodine motor with the control, contact...

 Open the catalog to page 10
Type ABL-3905 and ABL-3907-11

Output For Motor Power Connections Acceleration/Deceleration Power Supply Trim Potentiometer Connections Commutation Sensor Inputs Control Inputs MAX Speed Trim TORQ Trim Potentiometer Potentiometer ** Provided Terminals Figure 3 – Control Circuit Board Terminals (Included on Both Models 3905 & 3907) Two 16 AWG terminals are provided for the power supply connection to the control. Bodine’s stock 24V BLDC gearmotors and motors are supplied with the appropriate size terminals for the motor power lead connections. Also included are five terminals for 10-12 AWG wires. These are to connect the control...

 Open the catalog to page 11
*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.
About DirectIndustry
DirectIndustry is a marketplace that offers B2B players a complete experience, from product sourcing to purchase. DirectIndustry is an entity of VirtualExpo Group.