Models 0790 & 079

 Models 0790 & 079

Models 0790 & 079

Product catalog summary
Specifications
The document outlines the specifications for Bodine Electric's WPM Filtered PWM Speed Controls for Permanent Magnet DC Brush Motors, specifically models 0790 and 0791. Key specifications include:
  • Input Voltage: 115 VAC ±10%, 50/60 Hz, single phase
  • Maximum Input Current: 2.5 Amps RMS for Model 0790 and 5.7 Amps RMS for Model 0791
  • Output Voltage: 0-130 VDC
  • Ambient Temperature: 0-40°C
  • Maximum Output Current: Continuous - 2.00 Amps DC for Model 0790 and 3.20 Amps DC for Model 0791; Peak - 2.20 Amps DC for Model 0790 and 5.00 Amps DC for Model 0791
  • Speed Regulation: 1% of rated speed
  • Acceleration/Deceleration Time: Adjustable, 0.1-15 seconds
  • Speed Adjustment: 10K Ohm potentiometer
  • Diagnostics: Green power LED, red current limit LED
Installation
The installation section emphasizes that only qualified personnel should install the control, adhering to the National Electrical Code (NEC) and other safety codes. Key steps include:
  • Mounting the control using specified mounting holes
  • Setting up horsepower and acceleration selector switches using dip switches
  • Making electrical connections with caution, ensuring the AC power line is the last connection made
  • Optional inhibit switch connection for motor control
Operation
Before starting, preliminary checks are necessary, including verifying fuses, connections, and secure mounting. Operating steps include:
  • Setting the speed pot to zero before turning on the AC power
  • Adjusting the speed pot to achieve the desired motor speed
  • Internal adjustments can be made using trim pots for fine-tuning
Troubleshooting
If issues arise, disconnect the control from the AC power source before troubleshooting. Common checks include verifying connections and fuses. If problems persist, contact a Bodine Authorized Service Center.
Warranty
Bodine Electric offers a limited warranty covering defects in workmanship and materials for twelve months from purchase or eighteen months from manufacture. The warranty covers repair, replacement, or refund but excludes incidental expenses and damages due to misuse or unauthorized modifications.
See more

Catalog excerpts

 Models 0790 & 079-1

OttFY MotioN. Instructions for Installation and OperationType WPM Filtered PWM Speed Controls for Permanent Magnet DC Brush Motors • Models 0790 & 0791, NEMA 1 enclosure SPECIFICATIONS Input Voltage_ Maximum Input Current, Continuous Output Voltage_ Ambient Temperature_ Maximum Output Current, Continuous Maximum Output Current, Peak Speed Regulation Acceleration/Deceleration Time Means for Speed Adjustment Means for Drive Inhibit_ _obtainable with most motors _switch closure green power LED, red current limit LED * Thermal rating only. Actual max. continuous output current is 1.25 Amps. INSTALLATION WARNING: This control should only be installed by a qualified person familiar with its operation and associated hazards. The National Electrical Code (NEC), local electrical and safety codes, and when applicable, the Occupational Safety and Health Act (OSHA) should be observed to reduce hazards to personnel and property. The control does not provide motor over temperature protection. The user is responsible for providing this protection in the equipment where this control is used (Remarque: La detection de la surchauffe du moteur n'est pas assuree par cette control). Step 1: Mounting the Control The control may be mounted using any two or all four mounting holes. The mounting holes have clearance for 1/4-20 or M6 screws. Step 2: Preliminary Setup HORSEPOWER & ACCELERATION SELECTOR SWITCHES-Control models 0790 and 0791 are packaged with the enclosure cover unattached. Remove the cover to set the horsepower and acceleration selector switches. Figure 4 shows the location of a bank of 8 dip switches. Set switches 1 through 6 to match the type, speed, and current ratings on the Bodine motor nameplate per Figure 2 (consult Bodine on settings for non-Bodine motors). Set switches 7 and 8 to select the acceleration/ deceleration time range per Figure 3. Step 3: Electrical Connections The enclosure cover must be removed as shown in Figure 4 to make the electrical connections. WARNING-All parts of the circuit operate at voltages capable of causing serious injury or death. WARNING-The AC power line to the control should be the last connection made. CAUTION-The control board signal common is not at ground potential. Any external signal or equipment connected to the control must be electrically isolated from ground. INHIBIT SWITCH (OPTIONAL)-A mechanical switch or relay with contacts rated for low voltage may be connected to terminals "H1" and "H2". With the switch open, the motor will run. With the switch closed, the motor will coast to a stop. WARNING-The inhibit switch should not be used to disable motor or control when servicing these or driven equipment. Disconnect the AC power instead. 1. For armature speed of a geared motor, multiply the output speed at the driveshaft by the gear ratio. 2. If the user desires to install their own armature fuse on the control output to protect the motor from continuous overloads, base fuse ratings on the motor rating in this column. 3. Peak current available with TORQ pot in fully CW position (factory setting). This current exceeds the continuous rating of the motor and is for intermittent overload conditions only. 4. Use this column for sizing a line fuse on the control input. 5. The REG potentiometer must be turned fully CCW (off) for high-speed type 24ABEPM motor. 6. Time for voltage across A1 and A2 to ramp up to 130 V when speed pot is turned from 0 to 100; or to ramp down to 0 V when it is turned from 100 to 0. The time for a motor to accelerate from 0 to 2500 rpm or decelerate from 2500 to 0 rpm is dependent on motor size and loading conditions. www.bodine-electric.com | [email protected] | 19225 Kapp Drive, Peosta IA, 52068-9547 U.S.A. | Tel: 773.478.3515

 Open the catalog to page 1
 Models 0790 & 079-2

INSTALLATION, continued MOTOR CONNECTIONS–Feed the motor cable through the opening in the bottom of the enclosure. For clockwise armature rotation, connect the “+” motor wire (white wire on Bodine motors) to terminal “A2” and the “–” motor wire (black wire on Bodine motors) to terminal “A1”. For counterclockwise rotation, reverse the motor connections. Reinstall enclosure cover. LINE FUSE–Models 0790 and 0791 are equipped with a fuseholder on the front panel that is accessible to users for field replacement of the fuse. A four amp fuse is factory installed in model 0790 and an eight amp fuse...

 Open the catalog to page 2
*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.
About DirectIndustry
DirectIndustry is a marketplace that offers B2B players a complete experience, from product sourcing to purchase. DirectIndustry is an entity of VirtualExpo Group.